Jump to content
SAU Community

Recommended Posts

Am now reminded why I don't play footy most Saturdays...no sleep in f**king sucks.

f**king idiot crashed the merc before i could pick it up

what a f**king waste that thing was an animal. picking up my deposit tomorrow

i cannot be f**ked finding another car dead set f**k my life

/rant

Willing to bet the guy went on a last minute thrash n burn before selling the car to you...makes me wonder how many people actually do that and f**k the car.

Yeah I'm close enough lol. Theres a silver over grey S1 I've seen around reservoir area a bit as well.

Lol where abouts are you from again?

Rimon- that sucks man, not meant to be i guess

way to many stance sites now its just a joke.

stancenation

stanceworks

hellaflush

stanceiseverything

stanceyamum

yeh bad

was posted by a mate on fb

still think its pretty good for a truck, but in US they go nuts for modded trucks there

f**king idiot crashed the merc before i could pick it up

what a f**king waste that thing was an animal. picking up my deposit tomorrow

i cannot be f**ked finding another car dead set f**k my life

/rant

that sucks mate but im sure you will find another one.

true, but men with balls drive RWD

and real men with balls and a dick drive evo's :P

9-9:30 is a sleep in when u wake up at 4:30am weekdays. Gotta be at the ground in 95 minutes.

Unlucky rimon

Ya win? Lost by 12 in the last 5 minutes. Only motivation for trying to get into 1sts would be so I can play arvo games lol. But then the midweek training would piss me off.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...