Jump to content
SAU Community

Recommended Posts

This is interesting. I have no powerduct, but I did run for a few months with the little panel on the airbox removed. Not sure how much difference the powerduct would make vs not having anything there. The airbox sits so close to the front that I figured the only difference would be that it might suck in hot air when I wasn't moving, but in theory that should be better for fuel economy, not worse.

Recently I put the little plastic panel back on and realised the difference it made. With the panel back on again, I now have much better low-end response, smoother power delivery and the car feels noticeably faster. Fuel economy also seems to have improved a little, but not by enough to make any great claims about it. The main difference was in the ability to build boost at low revs...it seems having the airbox closed is good for building boost pressure early.

Top end performance was definitely improved with the panel removed, so I may have had a heavier right foot more often...

hmm... I put a Powerduct on last weekend and noticed an improvement in responsiveness almost straight away (my CAI has been disconnected until I make a new one that fits with the front bar). The difference was like trying to suck air in with your hand over your mouth (closed airbox and only stock funnel) as opposed to just breathing normally (with Powerduct).

Didn't really notice any additional sound although it may be a bit difficult to hear over my turbo and exhaust :banana:

The engine does seem to have a bit more of a sense of urgency about it with the duct on.

To each their own I guess, but the thinking that turbo cars need as much air to the intake as possible would make you think that the Powerduct would be more a positive than a negative for our cars, no?

I don't see either how by limiting air intake it could make the turbo spool any earlier.

It is hard to imaging how it could help low down power but perhaps it is like the opposite of a restrictive exhaust on a NA car where that helps torque.

From memory it is just a small difference anyway but I kept mine off as I liked the feeling it made to the power delivery at the top end.

Cheers

Andy

I dont understand why mine felt faster when I put the little panel back on. I cant explain it. But it definitely does seem faster or at least more responsive off the line now. It doesn't make sense...

There must be a reason why Nissan included the powerduct with all n/a versions of these engines and not with the turbo version.

emissions

I dont understand why mine felt faster when I put the little panel back on. I cant explain it. But it definitely does seem faster or at least more responsive off the line now. It doesn't make sense...

There must be a reason why Nissan included the powerduct with all n/a versions of these engines and not with the turbo version.

  • 1 year later...

going to reactivate this thread.. hoping someone has worked out something to fix the fuel gauge.. mine is shocking can jump a quarter of a tank between starts.. i am on gas though like to keep at least a 1/3 in the tank.. though every few days it says i am near empty..

anyone got a fix?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...