Jump to content
SAU Community

Recommended Posts

I went from a garrett gt42r with a 1.01 rear to a 6466 with split pulse T4 1.00 rear thanks to PJ.

at 24-25psi i went from 426kws to 415kws but gained 100kw in the mid range. difference between the two is night and day.

this is on a supra 3L stock motor and pump fuel only.

it coota it ran 125mph on a runway surface with the 6466 and at wsid with the 42 the best i managed was 121mph

I just watched a Supra getting tuned, it easily maxed the 700kw dyno. lol. Seems the 6boost manifold overboost issues are still common across the range. :/

Precision turbo but I didn't find out what size. I only know it was massive and had a 5 inch inlet.

I also helped get the VL RB30 started, and got the 6766 spinning. Is it common to hear bearing noise with the ceramic bearing cartridges? There is oil supply but the bearings sound flat spotted. Perhaps they need to get hot before the clearances close up?

Scotty. Was the oil restrictor removed? If it was you have almost certainly put the restrictor back in the wrong recess of the chra. There are 4 recesses and only one lines up with the restrictor. If you have it in the wrong one it pushes the chra out of round and you get this bearing flat spot noise and noisy bearing.

I also helped get the VL RB30 started, and got the 6766 spinning. Is it common to hear bearing noise with the ceramic bearing cartridges? There is oil supply but the bearings sound flat spotted. Perhaps they need to get hot before the clearances close up?

My 6466 sounds like this. After 500km its free'd up slightly but you can hear the 'tink tink tink' noise as the turbo spins down just before it stops completely. Still boosts fine and is plenty responsive. Might email Precision.

A mate's 6262 is quite noisy also but I thought it was just the thing with roller bearing turbos. It was actually really hard to spin when it first went on the car but seems to have free'd up nicely now. My brother's GT30 is noisy as hell, even after it was reco'd

I've had a buggered precision 6262 roller apart before and it only had one hole in the centre cartridge for the oil restrictor to locate into, the drain hole on the opposite side was more than half the diameter. Wonder if there's a few different assemblies they use

Dave thats going to be one result ill be anticipating, 6262 TS on a Neo doesnt seem to be existant out there. Is its just the turbo and lines your changing

ditching the DE runners for DET, 4 inch dump and highmount 6 boost, new ECU and getting my VCT back

current setup is lowmount Hypergear with DE runners and faulty ground on VCT which will be fixed when it gets the ECU

ditching the DE runners for DET, 4 inch dump and highmount 6 boost, new ECU and getting my VCT back

6 Boost? I hope the wastegate exit off the manifold is welded on the correct angle, Kyle won't entertain the thought his manifolds are badly designed, so won't fix the simple design flaw. You should be right though, as the boost spiking is the tuner's fault apparently.

Nice, lucky i didnt buy the runner off you. I just have to get a highmount mani then chase for gold.

I have two of them so you can still have the spare if u want it!

6 Boost? I hope the wastegate exit off the manifold is welded on the correct angle, Kyle won't entertain the thought his manifolds are badly designed, so won't fix the simple design flaw. You should be right though, as the boost spiking is the tuner's fault apparently.

you just had to make me go dig it out of its box and unwrap it just to check didnt you!

would of preferred a more even flow but a 90degree shouldnt be so bad.. if it spikes ill just run what it puts out! 35psi for all!

NDq8uYV.jpg

Got the car tuned the other day at Unigroup and the Precision 6766 is a weapon of a turbo. We opted for the 1.0 T4 split pulse rear end. We used to have a good old T78 on the engine, its an RB26, and at the same boost the 6766 is about 55rwkw up. All we changed was the turbo and dump pipe

We ended up with a consistant 485rwkw at 25psi on E-Flex which is currently showing around E60. Going to get some United E85 and see if we can crack 500rwkw with a bit more timing. I dont want to run any more boost so what it makes at 25psi is what its going to make ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...