Jump to content
SAU Community

Recommended Posts

Right here is the problem/problems.

1st thing the mods i have are: Big Pod filter, 3inch to 3 and half inch straight through exhaust with 2 resonators and split dump pipe, dsr heavyduty coils, new spark plugs, turbotech boost t. Everything else is standard

So i had the problem of not being able to boost over 10psi with the factory ecu going into R&R. Even when i set it to 7psi it still spikes well over 10psi and is sluggish until it hits the set psi on the boost t, which is weird in itself because it shouldnt be doing that.

So i went and got a mines ecu for my car and it works fine apart from it not liking me boosting over 10psi as well! its not as bad as R&R but has exactly the same feeling. So now i know that it isnt a electronic problem or is it?

My car feels way under powered and sounds like it should be boosting flat out but doesnt move as fast as it sounds.

I thought it could be tired fuel pump or clean the afm?

Tell me what your thoughts are and what i should do?

Everyone please help so i dont end up selling the wee beast.

Link to comment
https://www.sau.com.au/forums/topic/326789-is-my-car-impossible-to-make-faster/
Share on other sites

  • Replies 126
  • Created
  • Last Reply

Top Posters In This Topic

Well to answer the topic's question, no. Spend some money and reap the rewards. EBC should stop the boost spiking, if that's causing R+R, and/or get a REAL ECU. One that doesn't have R+R, and has to be tuned. It won't be cheap, but will surely be worth it.

Wack it on a dyno to sort out the issue, or get a an aftermarket ecu and then wack it on the dyno. Or even better go to a tuner, talk to them and tell them what power you are after, and they should tell you what types of mods you need. Your wallet will also have to get a bit lighter.....

ok so about the ecu

its an aftermarket mines ecu so how would it have the restrictions of the standard ecu? and if my car does the same thing on 2 different ecu's then how would another one help?

what would the fuel cut defender do for my car?

I will probly take the car into NZEFI later in the week and get them to see whats going on. but not looking to spend that much more money on this thing. with the mods i have and the ecu it should be around 200kw as is. but i think its more around 140kw as on the factory ecu my best quarter mile time was only 15.5 wtf!

so now you all know how slow my car really is.

just sell it . if you were going to buy an ecu and tune it you would have asked about that

you obvoiusly cant be f**ked so just sell it

or expect a big lecture

and i wana keep it and already looked into spending 2g on a power fc and tune and would be happy to do that. the mines is there because its meant to get more out of my car while i save up for the power fc. but looks like not even a power fc will work atm. trying to figure out if i need to spend heaps more money just to get it to run perfect.

There is more to ecu's than a pfc or a mines. Heres a humungus thread on the VIPEC ecu http://www.skylinesaustralia.com/forums/Pl...ng-t218179.html

There are also several other brands you could go, ie nistune, autronic etc. Do a SEARCH, readup on the forums, go to a tuner and tell them your budget anf your issues, and diagnose your problem.

If your in NZ you could also try a LINK ecu perhaps.

There is more to ecu's than a pfc or a mines. Heres a humungus thread on the VIPEC ecu http://www.skylinesaustralia.com/forums/Pl...ng-t218179.html

There are also several other brands you could go, ie nistune, autronic etc. Do a SEARCH, readup on the forums, go to a tuner and tell them your budget anf your issues, and diagnose your problem.

If your in NZ you could also try a LINK ecu perhaps.

yea i read up about that but thats alot of money. im just trying to find out why my car is doing this tho because it couldnt be electronic could it? not on 2 completely different ecu's.

First thing I would do if I havent figured out the issue myself would be to take it to a tuner, and get it dynoed, at least then you will see what the car is doing Air/Fuel wise, and boost wise. Then take it from there.

First thing I would do if I havent figured out the issue myself would be to take it to a tuner, and get it dynoed, at least then you will see what the car is doing Air/Fuel wise, and boost wise. Then take it from there.

ok sounds good i will pop into the tuner tomo and see what they can do.

mines ecu is just a remapped stocker, it will still do the same R+R when you get towards the end of the map, just not quiet as bad like you said.

buy a real ecu and get it tuned, my pick would be nistune with a z32 ecu.

and realistically, not many 25s make over 200rwkw with the standard turbo, usually around 180-200 depending on the dyno and other mods

Edited by JonnoHR31

I thought I read it all... but what car again???? Also what turbo????

I'm assuming RB20DET? if so with those mods working well i'd expect around 140 - 150 rwkw, not 200rwkw - as the limit is the turbo. (If RB20 + RB25 / VG30 turbo expect around 180 - 200 depending on boost - but again this depends how much boost you want to run due to ceramic and steel wheels in the turbo)

AFAIK the mines ecu will still R & R - it is just a different map to provide better gains to suit a specific setup. The FCD is a cheap option to get around the R & R when running more boost.

If it's RB25DET then with the addition of a FCD and R & R not taking over (regardless of std / mines ecu) i'd expect around 180 - 200rwkw from 10 - 14psi.

At the end of the day, as everyone has said take it to your tuner they should be able to offer cheap options as simple as a HKS FCD and power run with slight tweak to get AFR's decent to the PFC you speak of and Full MAP tune.

Edited by huddy

Sell the car - you didn't read the advice you got on your last thread or else you would know why the Mines is not doing the job. You should have got EFI to chip the stock ecu and dynotune the car and got yourself a new fuel pump.

If you still have the Mines ecu ask EFI if they can tune it and if not bin it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...