Jump to content
SAU Community

Recommended Posts

Im stuck between a rock and a hard place(probably just another rock). I know my front shocks are very tired, and the rear are so-so. I went to pedders and the quote for all 4 shocks was $1200. WOW!!!,(and not a good wow either). Anyway, so now im stuck with the decision to either do that or spend the equivelant and go with coilovers. 95% of use is just street use, which in Tassie is moderate condition roads.

I still would like comfort, but as im intending on going from a stock 33 gtsts(154rwkw) to just a slightly better 200rwkw, then maybe having some coilovers will provide just that slightly better balance to the car. I have some fantastic windy roads near home that can be heaps of fun aswell.

Do i sacrifice some comfort? bearing in mind i have a mangled disc in my spine too(so a hard ride will hurt).

My price range for some coilovers is up to $1200 so any advice on models would be mucho appreciated. I would like to avoid the junk, but also not blow a budget.

Edited by cptpugwash
Link to comment
https://www.sau.com.au/forums/topic/328325-coilovers-or-spring-and-shocks/
Share on other sites

Theoretically, every suspension combo for a R33 is a "coilover"?

If you have windy roads, you want swaybars for handling. So you can afford to run slightly softer suspension. The best is going to be Bilsteins or Koni in the shock department, but at $1000 per end puts it outside your budget. If you can, maybe some KYB shocks with a Kings low spring and upgraded swaybars would seem appropriate (although that total combo is likely to be outside your budget as well).

First things, everyone will be itching to tell you that because Skylines run wishbine suspensio rather then Macpherson struts, they run "coil overs" std.

So i take it you mean an adjustable coil over with rebound/dampening adjustment and height adustment vs a non adjustable arrangmenet.

Adjustable stuff does not have to be harsh and crashy or racey. They can be whatever you want them to be. Look around for pricing on Koni and Bilstein then compare that with Tein Super Street etc. Just stick with a spring rate not much higher then std and the thing will deive nice.

If you nominate a budget it is easier to offer suggestions

$1200 for height Adj only Bilstiens and $300 for King springs, that's what I paid and they are awesome.

The car is a pleasure to drive even on bumpy roads and handles much better than the G4 coilovers they replaced.

Also the car is much more stable on high speed corners when hitting a rumble strip or edge.

the off the shelf bilsteins and kingies are good if u want something street friendly that ur never going to touch again. personally i think they are just too soft to get close to the cars limits for any real hard driving though.

So supersprints are not getting close to the cars limit ?

I'm faster now than with the harder ones they replaced !

So as a street and supersprint/trackday friendly suspension set up they are the best compromise for not much money, if you want hard suspension for driving around be my guest but I got sick of a horrible ride around town and something that when clipping rumble strips it would upset the car to the point of near loss of control.

I did replace G4 coilovers though which are a cheap option, which was still more than the OP was interested in spending.

yeah sorry to say I don't see you picking up decent suspension for $1200. Most of the cheap coilover kits are best described as harsh, they generally run high spring rates and hard shocks to feel "racey".

new standard type shocks to replace what you have + sway bars is the best way to spend 1200.

BTW I disagree about off the shelf bilsteins being too soft. I run them on the race car and they are excellent for such a (relitively) cheap shock. I would have to pay $5k+ to get something better. Soft is good to an extent (or at least, harder is not always better) because it helps keep the wheels on the road.

the off the shelf bilsteins and kingies are good if u want something street friendly that ur never going to touch again. personally i think they are just too soft to get close to the cars limits for any real hard driving though.

I got the bilsteins, they are not adjustable, and have the bilstein springs i think (blue ones) they are awesome if you hold your line right through the apex they hold beautifully, if your turn in too sharp they can dip , giving the impression they are too soft but really you just haven't taken the corner properly..

They are really comfy and perfect for speed humps too, people are constantly amazed at the speed i approach them, its not super low,but it is low...Scrapes leaving my driveway...And thats with the not low S1 bumper

So for everyday, id give them the :P If you can afford them cause i absolutely love them....Really just depends if you want then adjustable...if you set a street car up right first time you want need adjustables anyway.

Edited by Arthur T3

I guess if i wait an extra week or two i might be able to up my budget. But after looking at the price of Tein ss, $2000-$2400, maybe not that much. I have had a glance at the K-sports($1750), and they have some great features, including the montube which from alot of the info ive garnered, are advantageous over the tt.

Another reason i would like some adjustable coilovers over the factory setup is the ability to lower it ever so slightly. Maybe only 30-40mm, any more and i would be hitting the bitumen a fair bit as i occasionally do now. Also any lower would firm it up so much my back would be screaming in agony. Spending $1200 at pedders just for some shocks seems a real waste.

i was going to put in the KONI yellow shocks into my R33 but i bought some coilovers instead just because of there ajustibility and i want to drift so suited the driving style more, i am selling mine if your after a cheap set of shocks :thumbsup:

$1200 for height Adj only Bilstiens and $300 for King springs, that's what I paid and they are awesome.

did that but with basic sports bilsteins that have circlip height adjustment not a thread like coilovers. fitting them in 2 weeks time they are replacing flogged out OEM shocks and springs.

i would not go coilovers in a daily, you are paying for height adjustment, springs that are usually too hard and a cheap shock absorber unless you spend a good deal of money.

Hi mate, just letting you know that we are currently having a sale on the ISC N1 coilovers. Normally $1499 but we are selling 10 sets for only $1199. Once these sets are gone the price will go back to $1499. If you have any questions feel free to send me a PM or email me at [email protected]

Thanks, Ryan

+1 for bilstein shocks and king springs. I replaced some japanese ohlins coilovers with these and its sooo much better. I did gain some more body roll but with sway bars its all gone. Now I fly around corners smoothly taking the bumps instead of bouncing around loosing traction at bad times.

Best thing I have done.

Any coilovers for $1200 will be shit for the street.

U won't get Bilstein shocks AND King springs for $1200.

Just get a full set of new Bilstein B6 shocks and get a couple more circlip grooves machined into em to lower em using stock springs.

Edited by bradsm87
Any coilovers for $1200 will be shit for the street.

U won't get Bilstein shocks AND King springs for $1200.

Agree with the first statement, although I reckon they will be shit full stop.

Agree with the second, but Bilsteins are around $1100 a full set and Kings are $300 a full set. So $1400 has you laughing, what's 200 bucks to do it properly?

$1100 for Pedders shocks - you've got to be joking.

The pedders quote was for $1200, and yeh, i was a bit shocked(no pun intended). But since then i have heard personally and read a few bits aswell about how pedders are a rip off.

I have also contemplated just getting a quote elsewhere, get the shocks done and actually sell my loved r33. I may be in a good position in about 8 months to look at maybe a 96/97 gtr. Truth be told, it was a gtr i wanted to get 6 years ago, but they were all $35,000 or more for a tidy one. Now there are alot around $23-25,000.

So, spend $1500 on suspension?, then look at exhaust, inlet, intercooler?(another $3,000). OR maybe $900, then save my bikkies for a gtr?

WWJD??????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...