Jump to content
SAU Community

Burning A Set Of Plugs Every 8 Months To A Year?

gts-4 dreamer

By gts-4 dreamer,
in Engines & Forced Induction

 Share

Recommended Posts

gts-4 dreamer Mentor

gts-4 dreamer

Posted
Posted

I've put iridiums in etc and it keeps fouling them, it's always the same, starts getting hesitation up over 4k revs on load. revs just fine to redline when not loaded up.

have used standard gaps to begin with, only the usual issues. went .8 gap they lasted an extra couple of months. last time went one heat range colder and gaped to .8, last longer but now it's happening again. basically I get a year out of iridiums. Should I just buy copper and keep replacing them ? is that normal wear on them? I was under the impression they should last allot longer.

gts-4 dreamer Mentor

gts-4 dreamer

Posted
  • Author
Posted

I was thinking that there was something maybe wrong with my tune? they are supposed to last for 100$ or is that just bs? I thought fouling plugs every 20$k was what you would expect from copper or if something was fuged in the tune?

blind_elk Grand Master

blind_elk

Posted
Posted

So what was the heat range of the last set of plugs you fitted?

What mods do you have that might affect the heat range requirement of the plugs? If they are fouling, maybe the injectors are delivering too much fuel. Or maybe the timing is inappropriate to support any mods you have.

gts-4 dreamer Mentor

gts-4 dreamer

Posted
  • Author
Posted

The last set was one heat range colder but they showed slight signs of burning to hot for the plugs, slightly white so ill get a set of copper in the original heat range again.

baseline: it's all working cept a slight leak in the steering rack but that's not a massive performance issue >:rofl: replaced timing belt, replaced cam gears to "easily adjustable".

mods: usual "stage 1" engy mods.

fmic, 3" straight through exhuast. 2530 hair dryer. fuel pump was replaced with intank bosch outa fear, greddy ult to fool with the sensors. she could probably do allot better with a replacement ecu but not 1500 better so thats it.

SLIPPERY Experienced

SLIPPERY

Posted
Posted

i need to replace mine after a week if i move the car from the garage to the lawn to wash the thing haha....3 months out of a set of plugs is good for me and if copper plugs are good for close to 500atw then i cant complain for $30 a set

Brezza Proficient

Brezza

Posted
Posted

just like everyone says platinum plugs are a waste of $$

coppers are fine, and because they're cheap most people just replace them if they get fouled.

i replaced mine after a year, they weren't in too bad condition but i was doing coil packs and just decided to replace the plugs too because its just so cheap.

Harey Veteran

Harey

Posted
Posted
I do mine with oil every 5000km. You could also look at bosch plats, ~$40 for 6 from repco, they go pretty well. Not sure how long they last, prob not much longer than the coppers...

Thats pretty keen changing them every 5,000km on a stock car!

Galois Veteran

Galois

Posted
Posted
Thats pretty keen changing them every 5,000km on a stock car!

Finally got new coilpacks 2 weeks ago so I'll see how long they last. Car is pretty stock, tho i wrote "stock" a long time ago, before I realised that 14psi is not stock boost. The car's history is unknown lol.

Heaps of people on here just change plugs with oil to keep the car fresh and avoid misfires.

gotRICE? Veteran

gotRICE?

Posted
Posted
I do mine with oil every 5000km. You could also look at bosch plats, ~$40 for 6 from repco, they go pretty well. Not sure how long they last, prob not much longer than the coppers...

I do that too. Keeps it all fresh :D Only takes 30 mins or so extra. I just do it while its draining haha.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
Hence the reason you don't waste money on platinums and iridums in our cars. Waste of money as you never get the mileage out of them compared to using them on a normal car.

+1

Been saying it for years, even the Spark Plug 101 thread covers this off...

Yet people still waste money on iridi/plati :D

Probably not helped by a shit tune or poor plug heat selection though as a side point.

Either way go back to the normal coppers

blind_elk Grand Master

blind_elk

Posted
Posted
The last set was one heat range colder but they showed slight signs of burning to hot for the plugs, slightly white so ill get a set of copper in the original heat range again.

what bloody heat range were they (other than "cloder than previous")???????? moreover, which actual model of plug were they?

PM-R33 Grand Master

PM-R33

Posted
Posted
+1

Been saying it for years, even the Spark Plug 101 thread covers this off...

Yet people still waste money on iridi/plati :D

Probably not helped by a shit tune or poor plug heat selection though as a side point.

Either way go back to the normal coppers

Yeah I feel like I keep constantly telling it to people as well.

blind_elk Grand Master

blind_elk

Posted
Posted

never had a problem with plat / iri plugs, except for a recent intermittent misfire that fouled one. turned out to be a faulty (splitfire) coil, but i fitted a set of coppers while diagnosing the problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...