Jump to content
SAU Community

Recommended Posts

Well. maybe not today but.

HDI FMIC

slim line electric radiator fan

TurboSmart PB BOV(to be changed soon)

3.5" Dump pipe

Dump Back 3.5" exhaust

8000k Xenons

Greddy Informeter Touch

Ball Bearing Hi flowed Turbo(weeeEEEeeee)

Trans "lock up torque converter"

Trans reversed +/- for tiptronic

iPod compatible PA15-NIS install

Unfortunately it isn't tuned yet, just trying to put together the cash for;

plenum spacer kit(Cam)

Stock BOV

Trans Oil Cooler(Craig)

Walbro Fuel pump

650CC+ Injectors

eManage Ultimate

bigger suction pipe

and we shall see what I get out of this budonkadonk of a car :whistling:

I haven't done as much as others, but its a start right?

Well. maybe not today but.

HDI FMIC

slim line electric radiator fan

TurboSmart PB BOV(to be changed soon)

3.5" Dump pipe

Dump Back 3.5" exhaust

8000k Xenons

Greddy Informeter Touch

Ball Bearing Hi flowed Turbo(weeeEEEeeee)

Trans "lock up torque converter"

Trans reversed +/- for tiptronic

iPod compatible PA15-NIS install

Unfortunately it isn't tuned yet, just trying to put together the cash for;

plenum spacer kit(Cam)

Stock BOV

Trans Oil Cooler(Craig)

Walbro Fuel pump

650CC+ Injectors

eManage Ultimate

bigger suction pipe

and we shall see what I get out of this budonkadonk of a car :)

I haven't done as much as others, but its a start right?

@Aaron is that Stage 1....lol! :D

@KV2 - thanks mate.....I cannot even remember writing that list :whistling: ....lucky the wife never found it :) .....ECU has changed now - NISMO/Emanage Ultimate(don't do Haltech) combo and 610cc injectors....motor's a bit broken ATM but should be back on the road later this week and then down for it's final tune!

@Aaron is that Stage 1....lol! :whistling:

Stage 1? what the turbo? i dont know he said something about gt30 fans or. its when i was new to the turbo. so he did it n i paid him lol

and what do you mean stage 1? arent you at stage negative 10 Mr Flinstone? hhaah joking

hey english conversion, gimme gimme

Front was 90mm off the ground. Too low!

I'm contemplating importing some Teins to fix the problem for good. I'm not sure how good the factory shocks are, but the C34's I've been told couldn't stand up to the punishment of 100,000K's + Don't know if the M35 is any different. My car has done 70,000K's, so might be a little life left in the old girl yet?

Front was 90mm off the ground. Too low!

I'm contemplating importing some Teins to fix the problem for good. I'm not sure how good the factory shocks are, but the C34's I've been told couldn't stand up to the punishment of 100,000K's + Don't know if the M35 is any different. My car has done 70,000K's, so might be a little life left in the old girl yet?

Mine had 39xxx kays when I bought it & my rear shocks were wallabyted! The fronts were not far behind...

You never know though...

can you do mine too mate? im happy to not pay you :(

It was literally a 20 minute job :D It's been driving me bezerk!

I'm happy to not have you not pay me to not do it? Not? :D

If you want some tape I can probably hook you up. Either that or Con-Tact adhesive backed felt is good for this too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...