Jump to content
SAU Community

Recommended Posts

not sure, the machine shop can decide. the mains are pretty bad though and there is scoring so odds are it throw away. probably bent too, they normally are after this sort of thing.

this isnt meant to be the report my engine failure thread though, I'm sure there is one of those somewhere....

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

pulled the motor apart today, the the main bearings were f**ked although not spun yet, and the big ends were almost perfect (just some foreign damage, I guess as the mains died). Good call Dan

so 1 point to the oil analysis.

Does anyone have results for a motor just after run-in?

Who left the main girdle loose? That's about the only way you could do that kind of damage - either that or incorrect clearances.....like miles off

Duncan, change your engine builder and I guarantee all of your engine failure worries will go away. Its not just about how they build, its the advice they give that prevents these things from happening.

My first engine failure with them was the same sort of thing - bad clearances.

2nd was due to crap in the cooling system - my radiator literally came back brown and overheated cracking a head gasket.

3rd was bad rings (my theory is they re-used the old rings and only swapped over the head gasket when it blew).

In the end you can only blame yourself for taking it back to the same place. You will probably delete this post, either way its food for thought.

Joe, the shop you are thinking of have never built a motor for my race car. They have built 2 other motors for me and both are lasting well. And I'll never delete a post unless it breaks a rule :D

Dan I'm waiting for the engineers report...the workshop beleive oil starvation would affect the mains but not the big ends (initially). I don't understand that point of view so I had a 3rd party look into it.

Joe, the shop you are thinking of have never built a motor for my race car. They have built 2 other motors for me and both are lasting well. And I'll never delete a post unless it breaks a rule :D

Dan I'm waiting for the engineers report...the workshop beleive oil starvation would affect the mains but not the big ends (initially). I don't understand that point of view so I had a 3rd party look into it.

Yeah... NAH!

Big ends always go before mains, look at all the GTR's that crack their oil pumps. Big ends die, not mains!!!

"Elite racing" sound like they are on the right path, either loose girdle or massive clearance issues

^^^ yeah i lunched a one in cats car due to a dodgy sump and pickup arrangement (ASR or high energy built me one that fixed the issue) and it burnt the big ends due to oil starvation. soon as it (rb26) spins a bearing the cranks bend like a bannana and often crack near the radius.

Ive havent seen a 26 with damaged mains after oil starvation unless it was driven for an unreasonable distance.

Does anyone have results for a motor just after run-in?

we dont do engines anymore (no time) so dont do any more oil analysis, but based on previous experience after the first oil and filter change our are pretty close to being normal (no excessive anything) in all instances.

damn, id be depressed if i went through as many engines as you have :( good on you for keeping a positive attitude though!

i know some ppl that get depressed if their fuel pump decides to die and that's nothing compared to what your dealing with!

just a quick Q, what was your oil pressure like before you pulled the motor down as compared to when it was a fresh engine? ie did u notice a gradual drop in average oil pressure levels between track days?

Edited by snozzle

was about to ask this. surely putting the block through the hot tank would wash any old bearing material out?

or would sum of the oil galleries be farely hard to clean out?

but then again when u pull a block out of the hot tank you blast the shit out of all the galleries with the compressor so surely that would quiet easily blast out any shit the tank missed

Dave (and everyone else for that matter) this thread is not about why my engine failed. That discussion will take place off the internet with the workshop involved.

This thread is about oil analysis, and what typical and atypical results look like.

Hi Duncan do you have a local WESTTRAC,

as they have Sampling service & for $26 is a great price,

even if you get it sent & have then Email you result`s,

Duncan, thats good news about the workshop, i stand corrected on that matter. Either way you made the right choice!

Dave (and everyone else for that matter) this thread is not about why my engine failed. That discussion will take place off the internet with the workshop involved.

This thread is about oil analysis, and what typical and atypical results look like.

this may help;

http://www.oil-lab.c...sis_Reports.pdf

this guy's website is quite informative in terms of giving acceptable limits. there is also a forum where you can submit your oil analysis and get some feedback too.

http://www.bobistheo...id=50&Itemid=56

forum:

http://www.bobistheoilguy.com/forums/ubbthreads.php?ubb=postlist&Board=3&page=1

Edited by SECURITY

I have the results for Noels engine after 500km (same oil the whole time) and from memory the lead and copper were both under 1ppm

Iron was about 25 or so (which you'd expect from ring bed in)

I have the results on the computer at work so if I get a chance/remember, I'll post them up

Any amount of lead is bad. The crank should not make contact with the bearings so the lead should be virtually non existent unless there is something chewing away at the top layer. Every 'oil starvation' failure I have seen has always shat the big ends, never the mains. The only time I have seen mains wear on every single one is:

A: Customer fit clutch incorrectly causing the crank to be locked against the gearbox (twin plate). After 10,000km or so the thrust bearing took it's last rotation. ALL the mains were completely gone

B: Girdle left loose by previous engine builder - every main was cactus

Oil starvation will wear journals 3/4/5 first but due to the fact the mains feed oil to the big ends, even when starved, the mains are the first to get oil again and the big ends get starved more. Also due to the fact the big ends have 100 x the load on them and the squishing effect removes oil very quickly. It takes A LOT to blow every main. Then you said you have every big end pretty much ok. That tells me something was wrong with the mains, not just something WENT wrong.

I know this isn't supposed to be an engine failure thread but hoping to give you a better understanding of what may have caused it.

I personally use Wear Check Australia for our oil analysis. They cost ~$40 and are pretty clear to read. The results you showed were clearly engine fail but they suggested that it may have been normal for a running in engine. Lead and copper are big fail indicators. Iron not so much

As I'm just about to run an a new engine i was wondering what the advantage is in testing run in oil, as you would expect there to be all sorts of metals (EDIT! I mean High Levels) in there as things bed in (obviously you don't want to much bearing metals though). If you were only going to do one analysis would it be better to do it on the first change or say after 500-1000km's?

Edited by D_Stirls

Not really. On the first one you will see higher levels of iron but nothing too serious. If the engine is assembled clean, then there should be nothing more than that.

Doing an oil test after the first oil change (at say 500-750....or even 1000km) is probably the best way to go about it. Also with run ins, whenever I build an engine for a customer, I always do road run in. Dyno run in works but you need to factor in problems that may not appear in the first few hours of engine operation. Leaks etc. Take it slow. Do small runs at first and gradually go further after each check. Never leave the engine in one load point...always be accelerating or decelerating, never stay on cruise for too long and never idle for long. After 500km not so important.

If you change the oil at 500km, you can drive it 100km more and do an oil test then if you like. Make sure you take the sample just after the engine has reached op temp otherwise any particles will settle. Never poke the tube all the way to the bottom of the sump either...for the same reason.

You get the results back in a few days and hopefully you'll be near 1000km by then and ready for tuning

  • 3 weeks later...

Well....since the new build is finished I guess I will have some figures to post in the next few weeks, I intend to get the run in oil checked for interest. Will also check the proper oil after run in, tune etc.

BTW failure reason for the old motor was identified, a bolt head from the cam baffle bolts were found in the oil pump intake. Also explains the high (5x) iron on the oil analysis

interesting about the e85 and oils..

those running e85 what engine oil do you recommend for a high hp rb25?

very interesting, i dont think many people know about this, id be interested to no what oils people are using too, as i was considering a which to e85 now that i have a pump near home with it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...