Jump to content
SAU Community

Recommended Posts

Just got outbid on Mines ECU on YAJ only 5 minutes ago...Got me in the dying seconds.... >_<

post-12229-0-52720000-1314015986_thumb.jpg

Oh well.....

really?

i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?

Its possible the IM interface timing isnt spot on......

anyway, sucks that you missed out on it, would have been a nice toy!

really?

i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?

Its possible the IM interface timing isnt spot on......

anyway, sucks that you missed out on it, would have been a nice toy!

Yes, but it is 10mins, not 5.

Well that's what has always happened to me :(

No ebay sniping on Yahoo Auctions

Finally did the "wire" mod today.

I shouldn't work on cars after night shift; everything seems to take twice as long...

Edited by Daleo

Finally did the "wire" mod today.

I shouldn't work on cars after night shift; everything seems to take twice as long...

Tired, eyes a bit blurry & cutting wires at the ECU. Yep, recipe for success, lol.

Tired, eyes a bit blurry & cutting wires at the ECU. Yep, recipe for success, lol.

Lol, yeah, I might've checked everything a few (hundred) times before cutting; just to make sure.:thumbsup:

Car starts, and no fault lights.:banana: Going to wait 'till later for a test.

Mind started ticking away; had to go for a drive...:banana:

That's a surprisingly useful little mod!

Wired up a switch to reset if need be. Is it just a case of close circuit, tap brakes, fault gone?

Good work for doing the hard yards guys; riding your coat tails is a great thing.:thumbsup:

What was the "wire" mod again?

Ecu harness, Pink wire, blue trace; cut, insert momentary switch, have access to full throttle opening whenever you like.:thumbsup: Enjoy better low speed throttle response and no delay after brake application.

Every now & then, close circuit and tap brake to avoid ECU going into "Limp Mode"

Anyone else care to fill in any holes in my explanation?

And I edited your post for the (future)emanage people

Ecu harness, Pink wire, blue trace; cut, insert momentary switch, have access to full throttle opening whenever you like.:thumbsup: Enjoy better low speed throttle response and no delay after brake application.

once you notice something shifty going on afeter approx 100km, go for another emanage tune. much better than just resetting.

Is there any way to send a constant signal to the ecu on that wire so it thinks it's connected and won't need to be reset all the time?

Could you hook the brake pedal light switch to that ECU wire to give a signal everytime the brakes are used? I don't know what voltage it see's/needs, just thinking of ideas.

Edited by slippylotion

really?i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?Its possible the IM interface timing isnt spot on......anyway, sucks that you missed out on it, would have been a nice toy!

I don't use IM. I have a mate in Japan who was on it for me to 49,000Y (much cheaper for me this way - avoid IM's commission). I was trying to call him for the last half hour as i was watching the bidding get higher and higher to up the bid a bit, however couldn't get him on phone....I was stuck! You are right in that time is extended with YAJ - i just couldn't get a subsequent increase in bid on.....

I recently bought the ex Andy, then ex Aaron Impul ECU which i have here, and was only going to get this one to compare!

What were the specs that the comp runs with?

No idea?? That's why i was interested in comparing differences between this and the Impul...

What were the specs that the comp runs with?

No idea?? That's why i was interested in comparing differences between this and the Impul...

Mine's generic tune (from memory)

RPM limit raised to 7100 or 7300 (can't remember which)

Boost raised to 1.1bar

Speed limiter removed

Throttle remap

Fuel/timing remap

Of course, the end user could specify whatever the hell they wanted (2bar boost and 7,500rom for instance) and all Mine's state is "yes, but please consider the risk"

Take your word for that info Cam. There wasn't a great deal of info on the listing. Is that info straight from mines?

You probably already know but I left the wiring diagram books with Aaron for you to collect and borrow.

Is there any way to send a constant signal to the ecu on that wire so it thinks it's connected and won't need to be reset all the time?

Could you hook the brake pedal light switch to that ECU wire to give a signal everytime the brakes are used? I don't know what voltage it see's/needs, just thinking of ideas.

i doubt it, if it detects connection while the brake is applied theres not point in having it.its best and easiest to have a momentary switch

i suggested a timer circuit, or something hooked up to the water temp. so it gets brake signal till the engine gets to 70degrees. before then you arent going to need to hammer it

i suggested a timer circuit, or something hooked up to the water temp. so it gets brake signal till the engine gets to 70degrees. before then you arent going to need to hammer it

but who would go through the trouble of that? lol if commsman doesnt, i dont think anyone will.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • What an awesome idea to fit the facelift Lamborghini Diablo headlights. They are a perfect fit!
    • An update regarding the registration with the DVLA I sent off the paperwork the day after I collected the car from the port, two weeks later it was all returned with a letter explaining they have rejected the application. This was because the cheque was £20 short for the road tax (I used a price list I found online). Nevermind it is what it is, it was sent back to them the following day with a new cheque. Fast forward another 2 weeks or so, I called them for an update to be told it had been rejected. Yesterday (16th September) I received the documents back along with another letter, this time it was because I didn't put an X in one box on the V750 (personalised number plate certificate), which declared that I had the rights to the personalised number plate. Why this wasn't mentioned in the first rejection letter, I don't know, but it could have saved this headache. The documents were sent back today, so fingers crossed third times a charm and it'll FINALLY be registered on the road just in time for the bad weather (woohoo!) To cheer myself up I lowered the front 25mm, was sick of seeing it sit like a monster truck. No idea how much clearance I'll have getting on and off the driveway, I'll worry about that when I can actually drive it
    • You're going to miss not worrying about rust in the strut towers like the Skyline shitboxes out there
    • A few little updates that weren't filmed due to not taking long to do or not interesting enough for their own video. My new K&N Air Filter arrived, I went with an RU-4180 which matched the dimensions of the universal cone filter the car originally had.  The battery had gone flat, while that was charging I tidied up the spaghetti wiring at the bulk head and down the sides of the engine Next job was to swap the stereo The Kenwood harness had the female ISO plugs cut off and the male ISO plugs cut off the adaptor loom and joined with bullet connectors. I ordered in a repair loom through work and re-did it all. New Kenwood unit installed (Android Auto, DAB, Bluetooth, Reverse Camera) The bonnet/hood gas struts have been poor since collecting the car. I couldn't find any suitable replacements locally so took a chance on a pair from AliExpress.  The originals don't use a retaining clip to secure the cup onto the ball fixture, would explain why I struggled for 10-15mins trying to pry off the cups. The ball fixtures unscrew using a 12mm spanner, new ones are the same size. Sadly no photo of them fitted, you're not missing much lol The dished Momo steering wheel got replaced with my Momo Tuner, turns out I ordered counter sunk bolts for the horn trim ring (like they normally are for the steering wheel) instead of allen cap (flat seat)  A terrible photo of a Quaife style gear shift knob I've had stashed in my tool box for many years after purchasing the incorrect thread size (I can see a pattern emerging with ordering incorrect parts...) Also threw in a cup holder and a (empty) Boss Coffee can, because why not  
    • GT-R clearly the better choice! The 300 is certainly not insaly fast but has a decent amount of poke. Does a nice little drift around the corners with a decent amount of throttle. It's VERY predictable in a slide too.  Feels so progressive! People probably presume there's a 25 year old driving it based on my behaviour this week! 🤣
×
×
  • Create New...