Jump to content
SAU Community

Recommended Posts

Just got outbid on Mines ECU on YAJ only 5 minutes ago...Got me in the dying seconds.... >_<

post-12229-0-52720000-1314015986_thumb.jpg

Oh well.....

really?

i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?

Its possible the IM interface timing isnt spot on......

anyway, sucks that you missed out on it, would have been a nice toy!

really?

i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?

Its possible the IM interface timing isnt spot on......

anyway, sucks that you missed out on it, would have been a nice toy!

Yes, but it is 10mins, not 5.

Well that's what has always happened to me :(

No ebay sniping on Yahoo Auctions

Finally did the "wire" mod today.

I shouldn't work on cars after night shift; everything seems to take twice as long...

Edited by Daleo

Finally did the "wire" mod today.

I shouldn't work on cars after night shift; everything seems to take twice as long...

Tired, eyes a bit blurry & cutting wires at the ECU. Yep, recipe for success, lol.

Tired, eyes a bit blurry & cutting wires at the ECU. Yep, recipe for success, lol.

Lol, yeah, I might've checked everything a few (hundred) times before cutting; just to make sure.:thumbsup:

Car starts, and no fault lights.:banana: Going to wait 'till later for a test.

Mind started ticking away; had to go for a drive...:banana:

That's a surprisingly useful little mod!

Wired up a switch to reset if need be. Is it just a case of close circuit, tap brakes, fault gone?

Good work for doing the hard yards guys; riding your coat tails is a great thing.:thumbsup:

What was the "wire" mod again?

Ecu harness, Pink wire, blue trace; cut, insert momentary switch, have access to full throttle opening whenever you like.:thumbsup: Enjoy better low speed throttle response and no delay after brake application.

Every now & then, close circuit and tap brake to avoid ECU going into "Limp Mode"

Anyone else care to fill in any holes in my explanation?

And I edited your post for the (future)emanage people

Ecu harness, Pink wire, blue trace; cut, insert momentary switch, have access to full throttle opening whenever you like.:thumbsup: Enjoy better low speed throttle response and no delay after brake application.

once you notice something shifty going on afeter approx 100km, go for another emanage tune. much better than just resetting.

Is there any way to send a constant signal to the ecu on that wire so it thinks it's connected and won't need to be reset all the time?

Could you hook the brake pedal light switch to that ECU wire to give a signal everytime the brakes are used? I don't know what voltage it see's/needs, just thinking of ideas.

Edited by slippylotion

really?i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?Its possible the IM interface timing isnt spot on......anyway, sucks that you missed out on it, would have been a nice toy!

I don't use IM. I have a mate in Japan who was on it for me to 49,000Y (much cheaper for me this way - avoid IM's commission). I was trying to call him for the last half hour as i was watching the bidding get higher and higher to up the bid a bit, however couldn't get him on phone....I was stuck! You are right in that time is extended with YAJ - i just couldn't get a subsequent increase in bid on.....

I recently bought the ex Andy, then ex Aaron Impul ECU which i have here, and was only going to get this one to compare!

What were the specs that the comp runs with?

No idea?? That's why i was interested in comparing differences between this and the Impul...

What were the specs that the comp runs with?

No idea?? That's why i was interested in comparing differences between this and the Impul...

Mine's generic tune (from memory)

RPM limit raised to 7100 or 7300 (can't remember which)

Boost raised to 1.1bar

Speed limiter removed

Throttle remap

Fuel/timing remap

Of course, the end user could specify whatever the hell they wanted (2bar boost and 7,500rom for instance) and all Mine's state is "yes, but please consider the risk"

Take your word for that info Cam. There wasn't a great deal of info on the listing. Is that info straight from mines?

You probably already know but I left the wiring diagram books with Aaron for you to collect and borrow.

Is there any way to send a constant signal to the ecu on that wire so it thinks it's connected and won't need to be reset all the time?

Could you hook the brake pedal light switch to that ECU wire to give a signal everytime the brakes are used? I don't know what voltage it see's/needs, just thinking of ideas.

i doubt it, if it detects connection while the brake is applied theres not point in having it.its best and easiest to have a momentary switch

i suggested a timer circuit, or something hooked up to the water temp. so it gets brake signal till the engine gets to 70degrees. before then you arent going to need to hammer it

i suggested a timer circuit, or something hooked up to the water temp. so it gets brake signal till the engine gets to 70degrees. before then you arent going to need to hammer it

but who would go through the trouble of that? lol if commsman doesnt, i dont think anyone will.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did you pay with a credit card? I'd be putting a charge back through then finding a new sparky to sort it out. 
    • If you mean the alarm immobiliser; theyre internal to the alarm itself which makes that difficult; I couldnt even see where he put it; its not in the same place as last time; but with all black wiring it might be very challenging to trace  I had someone turn the key for me as I know it only primes for a couple of seconds As my post above; I am getting no voltage to the pump at all; but I am testing continuity of the power line (SB) from the pump plug to the relay fine. As well as the negative from the pump plug to a 12V constant.    Yeah; he blammed the no start on a bad battery; said I needed to get a new battery and it'll start. Turns out the battery drained because the tail lights had been on for half the day during the install (the rubber cushion on the brake switch gave out while he was testing it as I have a picture of the car from that morning with the tail lights off..i've replaced that). The battery was turning over the engine just fine for a long time; but got low since lights were draining it so it was too low to test a start after he finished. I bought a new one on his advice...$250 wasted. My original battery charged up just fine and is healthy.    It was running perfectly fine when I messed up the old alarm (programmed out the remotes). He couldnt start it after removing the old alarm; my assumption is that when he unhooked it; he didnt bridge the circuit back when trying to start it. Its always been perfectly fine. The ECU swap and pump were 2 years ago. It's never missed a beat in that time. 
    • This is a big issue for me without the diff. I just have zero drive from the passenger side when drivers side has no traction. Bec's parents place has a crazy steep driveway with odd camber and I have never been able to get up. My bro-in-law's 130i with an (unknown brand) LSD gets up fine as does their dad's Hiace. My car stays at the bottom. We have other odd camber roads around here as we're elevated a bit and if it's raining I can get totally stuck around some hairpins. 
    • Yeah, I am super excited for this.
    • Was the car running before he touched the car?
×
×
  • Create New...