Jump to content
SAU Community

Recommended Posts

Installed Dolphin triple gauge pod, the Defi's stand out slighly less now also thinking i'll install a bypass switch so i can turn the gauges off at night/ RBTs and such

Moved the AVC-R to the top of the steering column, Cant quite see 0-20Km and then 140+ on the speedo and bellow 2k on the tacho. Can't really imagine this being a problem and i can have the AVC-R display speed if i'm at the track/strip.

Instaled and M35 steering wheel a bit of messing around to get it to fit but it looks great. Anyone else done this swap? I haven't plugged the airbag in yet as it has been suggested to me that the C34 computer might not like the newer airbag and things could end badly...

Wraped a pair of Dolphin eyelids in carbon and stuck them on, they look ok but i think i'll give them a couple of coats of clear to get the genuine carbon look.

Installed new 55W/4300K HIDs, much brighter than the ones than the car had in it from Japan.

I should be getting the bodywork/kit fixed up in the next couple of weeks.

Oil change done with Royal Purple, Ryco filter, old stuff was pretty black, have decided i will now be doing them on 7,500kms rather than the 10,000kms the workshop suggested when i had all fluids changed when i bought it. Also attached the new AFM plug which has made a difference to the way it idles (in a good way). So pretty happy atm. Only have to get passenger side cv boots done as they are split and car will be perfect. maybe next payday i think.

Oil change done with Royal Purple, Ryco filter, old stuff was pretty black, have decided i will now be doing them on 7,500kms rather than the 10,000kms the workshop suggested when i had all fluids changed when i bought it. Also attached the new AFM plug which has made a difference to the way it idles (in a good way). So pretty happy atm. Only have to get passenger side cv boots done as they are split and car will be perfect. maybe next payday i think.

Don't leave it too long, otherwise you'll chew out a CV and that ends up a fair bit move expensive.

Just changed the oil and filter. Ended up with a genuine Nissan filter (probably a waste of money) and Motul 8100 Excess 5w40. Going to find something better for next oil change but it needed to be done. Pulled the turbo banjo bolt too and checked to make sure that it wasn't clogged, it was very clean so I'm guessing either the previous owner checked it or I am lucky enough to have a very well looked after car. Either way I'm happy.

Just changed the oil and filter. Ended up with a genuine Nissan filter (probably a waste of money) and Motul 8100 Excess 5w40. Going to find something better for next oil change but it needed to be done. Pulled the turbo banjo bolt too and checked to make sure that it wasn't clogged, it was very clean so I'm guessing either the previous owner checked it or I am lucky enough to have a very well looked after car. Either way I'm happy.

:thumbsup:

same here put in some royal purple and an oil filter change, pulled out the bango bolt and it was spotless but i drilled it out anyways

smelt that sweet coolant smell opened the bonnet and what do you know cracked radator top tank just what i needed one week from my wedding found a new better 3 core radator and new hoses and high flow thermostat and fitted it all now alls good and only cost $450.00 back on the road again

Fitted 350z D2 coilovers into the M35... Been laying frame all night. Tomorrow removing inner guards, rolling outer guards and changing tires from 245/45/18 to 215/35/18....

Pics up in the morning

D2 coilovers

ewwww

well someone f'ed up on my car

steering felt very loose on my way home a few days after my alignment

jacked it up and i was greeted by no split pins in both sides and the tie rod end castle nuts were very loose pinch.gif

ewwww

well someone f'ed up on my car

steering felt very loose on my way home a few days after my alignment

jacked it up and i was greeted by no split pins in both sides and the tie rod end castle nuts were very loose pinch.gif

FFS! How bloody hard is it to do a job properly...:rolleyes:

That's just pathetic; I hope you went back and gave it to them?

Don't leave it too long, otherwise you'll chew out a CV and that ends up a fair bit move expensive.

yeah i know i had the drivers side done the other week which is when they noticed that other side is split too, drivers side was the worst, ill be very lucky if i don't have to replace that as the inner boot was almost non existant, fingers crossed though.

FFS! How bloody hard is it to do a job properly...:rolleyes:

That's just pathetic; I hope you went back and gave it to them?

was thinking about it

maybe i will come monday

was thinking about it

maybe i will come monday

I think it's probably worth your while; that's a bloody expensive mistake if the car owner isn't 100% switched on.

Obviously don't go in and go bananas, but definitely see if you can speak to the owner, and have a rational discussion about the incident.

Mistakes happen, but if no one makes it known; they can't alter their work procedure. A simple tick sheet can avoid these kinds of issues.

Quick phone photo.. Proper cam photos later.

50mm clearance on chassis.. Can't even get a credit card between the guard lip and rear tire....

fark thats low, looks awesome! hows it drive ?

it looks awesome!!!

but i bet it handles like ass. no offence, but youve put your whole suspension geometry out of whack. i bet the LCAs are angled up all round.

TBH, handling isn't what i'm worried about... Considering I have a proper track car to take care of my speed needs. This really only sees city driving 50km/h, with the occasional beach cruise.

And from a quick look, nothings too badly angled. It handles better than it did before, i'll say that much... lol

Quick phone photo.. Proper cam photos later.

50mm clearance on chassis.. Can't even get a credit card between the guard lip and rear tire....

IMG_20111030_172949.jpg

Top stuff! :blink:

If I did that; I wouldn't even be able to get out of my garage...

I guess that would save on tyre wear.:thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...