Jump to content
SAU Community

Recommended Posts

They came up well!

thanks!

damn hard work on the hands sanding.. but so satisfying when done.

Took a while as I only have cordless drills so very low speed/ torque. For about 30 bucks in materials though a new lease of life

Found this thing waiting for me when I got off work today, freshly delivered from Sendai, Japan

zxce7qyl.jpg

btw anyone have access to the Nissan Fast software to run the VIN for me? Just want to be extra sure I did in fact buy an Autech 260rs, all the signs point to that but just want to be 1000% sure

  • Like 3

ahh they are such a great car aren't they :) post up or pm me the vin and i can check.

I used the Stagea to tow the Leaf to Bathurst and back on the weekend, it made easy work of a very heavy load as always. Very happy with how the car runs, even though it has over 300,000klm on it now

Big thanks to Duncan for running the VIN for me :)

Stopped by the local Super Autobacs yesterday after work and picked up a mount to hold my phone so I can use it as a navigation and picked up some good ol' JDM squash air freshener.

fDHVq8dl.jpg

Phone mount on the left side, obviously no phone in it because I used it to take the pic :P

C4rmOSBl.jpg

and some cheeky seat belt covers that I've had in every car since I was 16, they were a gift from a friend in high school for my 16th birthday

  • Like 1

Seemed to have developed a boost or fuel cut on hard acceleration in 2nd gear and sometimes 3rd. Not sure if what has happened but feel like the engine fuel and boost all cut for a second so I let off the gas for a sec and bang all good again. Any one with thoughts on what it could be boost cut, fuel cut ? Running 19psi on max rom tuned with Walbro pump 3" turbo back and intake.

Maxing injectors maybe?

Seemed to have developed a boost or fuel cut on hard acceleration in 2nd gear and sometimes 3rd. Not sure if what has happened but feel like the engine fuel and boost all cut for a second so I let off the gas for a sec and bang all good again. Any one with thoughts on what it could be boost cut, fuel cut ? Running 19psi on max rom tuned with Walbro pump 3" turbo back and intake.

Maxing injectors maybe?

don't know if you are running with EBC. if you have EBC, you can block stock boost sensor that could let you know it is boost cut or fuel cut.

with aftermarket ECU, maybe the problem is your 3" turbo back, it will increase your boost level.

btw, do you have boost gauge to measure the boost level?

i also have some fuel cut and EMU is on my hand now :nyaanyaa:

I have a ebc and gauge reading 19psi max boost. I deleted the stock boost solenoid a year ago. How can you tell if it's boost or fuel cut by blocking the solenoid?

You can just block stock boost sensor, then you never get 21psi boost cut.

See attached pic, No.1 is boost sensor

post-137368-14575287314881_thumb.jpg

Could the factory ecu re learn itself and try to adjust for the max rom

It does exactly that, although it is fast at learning, so I would have expected it to be sorted on the dyno.

If the AFM is hitting over voltage in one particular cell it will fuel cut like this, but the voltage this happens at changes depending on the cell.

Nathan, if it is boost cut I would expect the MIL to light up. I wonder if the AFM was clamped correctly... As I said I have no idea how they tuned the HDI mate.

You can just block stock boost sensor, then you never get 21psi boost cut.

See attached pic, No.1 is boost sensor

attachicon.gifImageUploadedBySAU Community1457528730.265377.jpg

thank you gents I blocked off the map sensor this morning drove it hard to work to see if any boost cut... Seems to have done the trick.

I wasn't getting a mil light when it was happening but seems good now I'll test over the coming days and see how it goes.

I wasn't getting any cut in the dyno or for a few weeks after the tune, just came on all of a sudden. The ECU does learn at a fast rate so not sure why or how it happened.

Thanks for everyone's help with this gents [emoji106][emoji4]

  • Like 1

Some new wheels on won on auction so will have to wait for them to get delivered.

Also bought a Transgo shift kit to liven up the gear box.

The guy i bought it from has only one left. $250 + delivery.

If anyone is interested, please let me know so can pass the details on ☺️

It does exactly that, although it is fast at learning, so I would have expected it to be sorted on the dyno.

If the AFM is hitting over voltage in one particular cell it will fuel cut like this, but the voltage this happens at changes depending on the cell.

This learning only happens off boost/low load for fuel.

Finally got my AMPerformance intake fitted, straight away noticed the extra flow.

Throttle more sensitive down low, less throttle needed to get the car rolling.

Haven't tested high rpm yet.

Thanks to Craig for fitting it, wasn't easy.

  • Like 2

Finally got my AMPerformance intake fitted, straight away noticed the extra flow.

Throttle more sensitive down low, less throttle needed to get the car rolling.

Haven't tested high rpm yet.

Thanks to Craig for fitting it, wasn't easy.

Nice, and it's up high that it's makes the most difference

spent some time this weekend exploring, trying to figure out what mods were already on the car, so far I've found:

Nismo Exhaust

Nismo Air Intake

HKS EVC 3

Apexi Turbo Timer

Coilovers (brand unknown)

Carrozzeria head unit

waiting to hear back from local shop about doing a full fluid change/flush and to have them inspect the car in more detail

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...