Jump to content
SAU Community

Recommended Posts

Its not like I'm going to do it every gear change. Just to launch it in first gear on the odd occasion

And yeah pretty much cause it sounds cool

Edited by stig mick

haha, yes i agree, redlining sounds mad, not like its bad for your car, when doing burnouts or you go drifting, you will hit redline a heap of times :D

just make sure you have a nice exhaust to go with it ;)

Well yeah kind of. I revved it to 7600rpm and got scared of doing damage so I took my foot off the throttle.

on my R33 it would go to exactly 7000 which was the redline and then bounce off the limiter in the R32 the redline starts with red dashes at 7000 then a solid redline at 7500 so I assumed the rev limiter should start at 7500

and for gods sake, do it when your engine is warm....... just saying, ive seen some people wreck their engines driving on the limiter when its cold.

also i think that every car with a ecu, at least ignition and injector ECU system has a rev limiter.

there was a bunch of chips being sold on the internet a few years back that removed limiter. ive personally driven an r32 gtst with (i can only assume) something similar.

it was pretty much stock except the thing revved right off the tacho. so above 9000 rpm. i couldnt find limiter lol.

car had many problems but amazing a spun bearing wasnt one of them lol.

EDIT

the bloke who owned it used to come on here. apex_sx or something like that

Edited by tm_r33

and for gods sake, do it when your engine is warm....... just saying, ive seen some people wreck their engines driving on the limiter when its cold.

also i think that every car with a ecu, at least ignition and injector ECU system has a rev limiter.

Of course I wouldnt do it cold, I NEVER take it above 2500rpm until the temp gauge is in the middle I'm sure the people who get stuck behind me in morning traffic are spun out that and R32 is being driven like a grandma but I want the engine to last.

Just out of interest If the limiter was removed would going just a tad over 8000rpm do any damage to the engine?

On stock internals?Then yes...eventually.

Nissan put a limiter on the max revs the engine will take,too risky going over it.

so just doing it once won't matter too much then?

if the limiter has been taken out i won't try it again

mine used to bounce at 7600-7700 with stock ecu. was slightly higher with nistue. but PLEASE keep it on the track!!!!!!!! on the street there is nothing more homosexual than wankers hitting limiter. its a true sign of a f**kwit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...