Jump to content
SAU Community

Recommended Posts

JECS is a generic manufacturer, like bosch

it would be a std item fitted to the car most likely, ie; OEM part

ok because i found some JECS 55cc injectors for rb25det so i was wondering are they anygood it does note remanufactured so does this man they are highflows however they are red tops

Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5619991
Share on other sites

ive also been looking at these injectors it says they are from factory injectors does this mean they have been high flowed or just remanufactured to flow 850cc

http://cgi.ebay.com/ebaymotors/6-JECS-855cc-Fuel-Injectors-Nissan-RB25DET-_W0QQcmdZViewItemQQhashZitem3cb36e9e18QQitemZ260708408856QQptZRaceQ5fCarQ5fParts

Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5621200
Share on other sites

From the advert

Remanufactured: A properly rebuilt automotive part. The item has been completely disassembled, cleaned, and examined for wear and breakage. Worn out, missing or non-functioning components have been replaced with new or rebuilt components. It is the functional equivalent of a new part and is virtually indistinguishable from a new part. See the seller’s listing for full details. See all condition definitions
Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5621239
Share on other sites

most likely they are rebuilt, high flowed injectors. your call but I would personally just buy new ones. injectors are not super expensive these days an are fairly important....

+1

and by the time you get them flow tested m, check spray patterns etc, you could have just purchased a new set anyway.

Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5622488
Share on other sites

I have tested a set of sard 700s once and they were all within a bees dick of each other. never bothered again with new denso type ones (sard/nismo etc). have tested plenty of standard injectors though and found a few % variance is the norm.

Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5622944
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
    • What Duncan said sounds right. Also, it looks like they only have the driver's mat. Not the rest. Because looking at the diagram: KG4911 is just the mat for the driver. KG4900 is the full set if I'm not mistaken and discontinued.   But, it looks like they may still have the full set for the manual S2. Might be worth checking for the other models as well as they seem slightly different. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/misc/G49 Man, I'm tempted.
    • I dunno about that as a blanket statement. Pitwork is Nissan's "Nissan genuine" thing, and for stuff like timing belts, I have found them to be excellent. Of course, for things like oil filters, you always use proper trusted brands anyway, not whatever the OEM has taken to using.
    • Ahhhh... If you were putting 12V to the led in there, that's likely made it very unhappy. Chances are how you put power, was 12V across an LED that's meant to only have about 20mA through it at peak, and a forward voltage of about 1.8 to 2.4 volts. That circuit is likely only a 3V3 circuit, and will have a resistor in series with the led too. That's my guesstimate on that light, without having touched one.
    • Another vote for installing them and see how you go.  I mean, you already own them, why would you not fit them? 
×
×
  • Create New...