Jump to content
SAU Community

Recommended Posts

  • Replies 204
  • Created
  • Last Reply

Top Posters In This Topic

Hey guys, time to mark reserves on the SAU GoProHD cameras. We have three of them for rent. Rental is $35 for the day. I will bring them to the track and help you set it up and learn how to work it.

They have a 16 gig card which is good for about 2 hrs of 720p HD video. That's about how long the battery will last too.

If you want to reserve one, pm me your details. See me and pay cash on the day.

If you want the video on the day then bring a BIG USB drive. Otherwise I will burn a set of DVD's for you and mail it back to you.

PM sent!

Entrants List updated as of May 16th from RENEW..

For those of you with Waiting on payment confirmation, give it a few days till the next update and if it still has not shown up please PM me so I can chase it up.. Thanks guys

oh and ONLY 3 SPOTS LEFT!!!

I'm just bringing my little proton hatchback and my brother is bringing his over powered, under braked and under tyred GTiR Pulsar

The over powered underbraked and undertired Gtir is awesome!

As sad as it is to admit I kinda miss that car. It made me laugh everytime you opened the throttle and gate started belching to atmosphere!

Hey folks - I need to get commitment numbers on the photography. Everyone loves getting pics of your car going 11ty at the track.

Last time we only barely got enough takers so we need to get commitment numbers in order to make it worth while for our photographers to make the trek to Goulburn.

PM me your name and car and I'll see you on the day.

WakefieldDVDOffer.jpg

Entrants List updated as of May 16th from RENEW..

For those of you with Waiting on payment confirmation, give it a few days till the next update and if it still has not shown up please PM me so I can chase it up.. Thanks guys

oh and ONLY 3 SPOTS LEFT!!!

Noob alert...

where do I find the entrants list to confirm names?!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...