Jump to content
SAU Community

Recommended Posts

How would XR6's be legal then? :mellow:

because they are an australian car brah.

or maybe, just maybe, it is because the restrictions are based off power to weight ratios (or just outright power in some states), the target value being under about 120kw/ton. the 350gt comes in well over this number since it's power output is 206kw (compared to the falcon's 195kw) and it weighs about 300kg less than the 1700kg falcon (based of the FG which comes in at 114kw/ton - the highest for any natro 6 cylinder falcon). in qld though the car must be under 200kw (plus non turbo, etc). this actually rules out the sv6 commodore, since it has 210kw, although it is right on the limit for some other states using the power to weight ratio rule.

  • Replies 165
  • Created
  • Last Reply

Top Posters In This Topic

Well NSW has the restrictions:

NO turbo

NO 8 cylinders or more

plus the following 6 cylinder vehicles

  • BMW M and M3.
  • Honda NSX.
  • Nissan 350Z and 370Z (including private or 'grey' import variants eg. Infiniti G35, Infiniti G37, Skyline 350GT (V35), Skyline 370GT (V36)).
  • All Porsches from 1994 models onwards (except diesel).
  • Mercedes Benz SLK350.

if you do the calculations you will find that pretty much all cars have a power to weight ratio of higher than 120kw/ton (which is what the old rule used to be. obviously they decided to change it to a simple list of restricted cars to stop people complaining because they put their car on the dyno and it made less than 120kw at the wheels so they should be able to drive it.

The smartest thing to do is rip all the things that contribute to the heavy weight of the vehicle. I mean, take out the sound-deadening, carpets, spare wheel. Remove the air-con unit, take all the glass out and just have nothing. Take the wheels and engine out of the car too and it will probably be faster than it was before.

actually fg xr6 goes really hard. my friend has one (auto), it completely demolished my NA R34 from second gear onwards after i dropped the clutch in 1st gear.

What do you expect? You're comparing a milk bottle to a wine cask.

Also, the XR6 is a family car. I'd buy one to tow my 32 to the drifts and take my grandmother out to lunch in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...