Jump to content
SAU Community

Recommended Posts

I'm thinking about turning my R32 into a drift car instead of trying to sell it.. I have the following shopping cart planned but my friend said I needed a few extra things.

My currently planned list:

  • Coilover Suspension
  • Suede deep-dish steering wheel w/ boss kit
  • sparco seat
  • fmic
  • LSD

However he's informed me that once I upgrade from wet roads to dry roads, I could risk twisting my chassis unless I install something like that brace that runs through the center of the car.

So that said, what else am I going to need for getting into dry road drifting (obv. I'm talking track)

Edited by SKITTLES
Link to comment
https://www.sau.com.au/forums/topic/367017-whats-needed-for-basic-drift-setup/
Share on other sites

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Lets see... what did I do to my car to make it driftable... I think I took it to Oran Park... pic related

n639839121_1630968_4930.jpg

On a more serious note, swaybars will make your slides easier to catch. Other than that you really don't need much, especially if you are just starting

basics

-locked diff. sure you can get a 1.5 or 2 way LSD but they are expensive and not required. Lockers aren't perfect but it's a drift car, not a time attack race car.

-a working clutch

-skid rims and tyres.

-remove HICAS

-alignment.

extras

-coilovers

-swaybars

Power isn't needed. You want the car to handle well and be predictable. Save funds for repairs, servicing and tyres.

Car damage is apart of drifting.

Edited by Peter89

So much torque, the chassis twisted coming off the line

win-one-internet.jpg

if it's a r32, an rb25 will be a good place to start, lol

*waits for all the RB20 fanbois to get sand in their vaginas

The original plan was to put an RB25 into it, seeing as the engine has 227,000KM on the clock. But the existing RB20DET is going stronger than my RB25DE with 165000km...

basics

-locked diff. sure you can get a 1.5 or 2 way LSD but they are expensive and not required. Lockers aren't perfect but it's a drift car, not a time attack race car.

-a working clutch

-skid rims and tyres.

-remove HICAS

-alignment.

extras

-coilovers

-swaybars

Power isn't needed. You want the car to handle well and be predictable. Save funds for repairs, servicing and tyres.

Car damage is apart of drifting.

12293_380244637013_520517013_3901770_4183248_n.jpg

This is pretty much my favorite pic atm.

Thanks for the tips though, I think I'll get a locker and use that for a bit before getting a 2 way lsd.

I don't know if it's got hicas, but i'll check it out tonight.

who teh fark said the chassis will twist and that you should out one of those pointless floor bar things in the car?

Well actually, the chassis will twist/flex a bit as soon as you sit in the car.

You callin' me fat? :P

So the floor bar thingo is pointless?

locked diff, no need to spend $1000+ on a LSD when a shimmed diff will do the same thing

a good seat, Velo seats are great and can get them pretty cheap

make sure the handbrake works to:P

thats all you need to start, anything else is pretty much extra

steering rack spacers are win and cost next to nothing

there are some basic engine mods that will help a lot (fmic, exhaust and more boost)

go watch some in car drifting videos, helps a lot at least knowing what you need to do

I was thinking of getting a $400 pair of seats hahaha just el cheapos... wonder if they're any good >.>

Yeah, gotta change the brake pads. I'll have to do the rear brakes, they don't seem to be grabbing the wheels too hard.

newbie question here,

Do you need any surge tanks or to change to a different sump, just wondering when your flying sideways wether theres still enough oil and fuel going in??

as long as you don't run low on fuel it shouldn't be a issue, stock sumps are fine to

Seriously, just drift it as it is. If you don't like an aspect of your car you will either quickly find out and change it or learn to just deal with it. Standard cars aren't undriftable, it's just harder :thumbsup:

Though... just to contradict myself, it is handy to have something to hold you in place. In my experience a harness with a factory seat works much better than an aftermarket seat with a factory seat belt. Grabs less attention from the police too ;)

Seriously, just drift it as it is. If you don't like an aspect of your car you will either quickly find out and change it or learn to just deal with it. Standard cars aren't undriftable, it's just harder :thumbsup:

Though... just to contradict myself, it is handy to have something to hold you in place. In my experience a harness with a factory seat works much better than an aftermarket seat with a factory seat belt. Grabs less attention from the police too ;)

Interesting thought about the harness....

As for leaving stock; the R32 has a lot of body roll and whilst it's still very driftable (not that I'd know >.>) it's a little unpredictable. Easier to stiffen the suspension and put some sway bars in before I head out.

Due to money, I can't get out on the track fo ra while, so might as well save up in the meantime for the gear.

newbie question here,

Do you need any surge tanks or to change to a different sump, just wondering when your flying sideways wether theres still enough oil and fuel going in??

For future reference; I've never had an oil problem with the car sideways, but I've only done it a couple times and was too busy watching other things.

I DO know, however, that when I was testing the brakes in it, I smashed them to the floor and the oil pressure (or whatever it is) guage suddenly dropped and the car almost stalled.

oil level might have been low.

for all RB's it pays to overfill the sump by half a liter.. cant go wrong with that. same with fuel in the tank. make sure its over half and there wont be any issues.

as for whats needed.. just an LSD that works.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • All trim back in wired running driving. Few things to follow up on but not far off the return to the road. att.6HN4wP38LTIOISkhA8eACoBFqzfgQMahZPLA8ut0pqE.mp4 att.w2q0ux2PGuqgQTj2Os13cNHQtqcSEcCAhD_CAXy_IQM.mp4
    • The trouble with phone apps is that they really do not know the sensitivity of the mic on each specific phone, whether there is some sort of cover or skin that can change that, etc etc. So the readings off them are not calibrated. You certainly couldn't be sure that you were even within 3 dB. I have the same app on two (actually more than that) different phones/tablets and the readings in the same room at the same time are never the same. I don't mind the apps - they are as useful as a dyno - if you're testing for delta from thing1 to thing2. But not to try to generate some sort of absolute value.
    • I'm gonna use the "Sound Meter" app from the Google Play Store and as close as I can bother to these procedures: 4. TEST METHOD FOR ALL VEHICLES EXCEPT PRE ADR83 IN-SERVICE GOODS VEHICLES AND OMNIBUSES 4.1 Microphone position 4.1.1 The microphone shall be directed towards the orifice of the exhaust outlet and shall be supported by a tripod or similar device not providing excessive acoustic reflection. The general requirements for positioning microphones are shown in the Appendix. 4.1.2 The nominal axis of maximum sensitivity of the microphone shall be substantially parallel to the test site surface and shall make an angle of 45 degrees ±10 degrees with the principal direction of gas flow from the exhaust. 4.1.3 In selecting the 45 degree alignment from the outlet of a motor vehicle fitted with two or more outlets, only the angle resulting in the microphone being farthest from any other outlet must be used. National Stationary Exhaust Noise Test Procedures for In-Service Motor Vehicles Page 3 4.1.4 The height of the microphone above the test site surface shall be equal to that of the orifice of the exhaust outlet ±25mm but shall not be less than 200mm above the test site surface. 4.1.5 The distance of the microphone from the exhaust outlet orifice shall be 500mm±25mm. 4.1.6 [Relates to vertical exhaust outlets] 4.1.7 For vehicles fitted with one exhaust outlet the microphone shall be placed so that the greatest possible distance is achieved between it and the vehicle. 4.1.8 [Relates to multi exhaust outlets] 4.1.9 [Relates to multi exhaust outlets] TLDR: 200mm off ground 45 degree angle relative to exhaust flow 500mm from tailpipe exit. (I probably won't use a tripod) Here's a photo, cause I read the instructions wrong myself.
    • No ABS, no TCS, no airbags, no cruise control, no lane departure assist, no emergency brake assist, no orange lights in the mirrors (continuously annoying me in multi-lane traffic), no stupid rear view camera. I am the one responsible for where my car goes and how it does it.
    • Cheapest Jaycar one is only $65.
×
×
  • Create New...