Jump to content
SAU Community

Recommended Posts

I finally got time to fit the GTX today, let me say now its bloody huge and only just fits in there. It sat a bit lower than I hoped too, I need to make a 90 degree oil drain to make it work. Everything else, although tight and time consuming, is easy enough to make now. Heres some idea of what I am dealing with...

Thanks Aaron for the help, we set a new record of 1 1/2 hours to remove the stock turbo. :thumbsup:

post-63525-0-49161300-1308835693_thumb.jpg

post-63525-0-36030700-1308835713_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/368795-gtx3071-install/
Share on other sites

Mmmm...

So when will it get fired up for the first time?

Plenty more work to do yet. :/

There is 5mm clearance from the gearbox housing and 10mm between the compressor housing and the chassis. Literally the minimum I would allow. Lucky our engine mounts keep it nice and tight so it should be fine.

Link to comment
https://www.sau.com.au/forums/topic/368795-gtx3071-install/#findComment-5880299
Share on other sites

Na, metal contracts when its heated. She'll be fine :ninja:

not if the engine tilts towards the firewal..

lol the first fit the wastegate entry was touching the wall.. i think after i left he re welded the adaptor.

Link to comment
https://www.sau.com.au/forums/topic/368795-gtx3071-install/#findComment-5880469
Share on other sites

dampers are shit and useless

engine mounts are the ONLY way to do it properly

i think the engine twists in the opposite direction anyway. but backing off might make it bump the sidewall?

i think the engine mounts are near solid anyway.. only better ones i think are the nismo ones which are completely solid..

agree with you on dampers.. havnt seen one thats worked as good as doing mounts.

Link to comment
https://www.sau.com.au/forums/topic/368795-gtx3071-install/#findComment-5880659
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...