Jump to content
SAU Community

Recommended Posts

So i seem to have a wierd issue with my m35.. just doesnt feel right under accelaration and numerous times the speed is going up though the revs are not.. (yes i know slipping is the other way round!) i must admit i am new to automatic gearboxes and this is the first i have ever owned and i might be simple paranoid though at approx 2800rpm and above some wierd shit is going on...

car pulls great up to then..though once it hits approx 2800rpm then the engine noise changes to what sounds like air blowing (yes thats very vague) and despite is still accelarates it doesnt accelarate well like it should..

just checked the transmission oil and its running way too much (about 1 cm above the full line when hot).. the oil itself doesnt look too old though it is not the red stuff i was expecting..

so how hard is to change the gearbox oil and filter? i have read Nulon or Matic S is the way to go.. how much work am i looking at and where do i get a filter? (350z is the same i presume?)

once again appreicate all your help.

Edited by Sage222
Link to comment
https://www.sau.com.au/forums/topic/373785-suspecting-gearbox-problems/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I had a similar issue when my car was worked on by the gas conversion mob.

It would rev up but then when it hits boost all I get is a crap load of hissing sound.

Scott looked at it and found some pipe was loose. Can't remember which one...

So i seem to have a wierd issue with my m35.. just doesnt feel right under accelaration and numerous times the speed is going up though the revs are not.. (yes i know slipping is the other way round!) i must admit i am new to automatic gearboxes and this is the first i have ever owned and i might be simple paranoid though at approx 2800rpm and above some wierd shit is going on...

car pulls great up to then..though once it hits approx 2800rpm then the engine noise changes to what sounds like air blowing (yes thats very vague) and despite is still accelarates it doesnt accelarate well like it should..

just checked the transmission oil and its running way too much (about 1 cm above the full line when hot).. the oil itself doesnt look too old though it is not the red stuff i was expecting..

so how hard is to change the gearbox oil and filter? i have read Nulon or Matic S is the way to go.. how much work am i looking at and where do i get a filter? (350z is the same i presume?)

once again appreicate all your help.

no its matic J, DONT put matic S in it!!!! it will destroy your transmission.

mine sometimes does that too, doesnt accellerate as hard as it should, i just kick it back a gear. its entirely possible youre not pushing the throttle enough to force the torque converter to unlock.

no its matic J, DONT put matic S in it!!!! it will destroy your transmission.

mine sometimes does that too, doesnt accellerate as hard as it should, i just kick it back a gear. its entirely possible youre not pushing the throttle enough to force the torque converter to unlock.

REally? Matic S will ruin the box? I thought S is better then J?

Isn't it Matic D that's bad for the tranny?

nah its not 5th i have confirmed it happens in every gear by driving round in manual.. ironpaw sounds like he had the exact same issue.. come on scotty you must remember what pipe!:)

its almost as the engine isnt seeing the boost..

Edited by Sage222

The box is suppose to be service free, unsure if there is a filter to change.

The fluid is simple to change, just warm the car up, drain the box via the lower plug.

Then drain the transcooler.

Replace the same volume of fluid as you drew out of the box and cooler(around 4-5 L) via the transmission fluid inspection pipe located next to the fire wall.

A full flush involves more work and uses a fair amount more fluid (8-10ish L?).

There are youtube videos for G35s/350z that can be of some assistance if you get stuck.

there is no filter, but there is a strainer in the valve body. its worth probably cleaning any metal bits out of that. but youll need to remove the pan.

just remember to check the fluid level after you have filled it. go for a short drive and check it again after.

What colour is it if is isn't red???

What was used in it and whom did the service?

I'd drop a little out of it (unhook one of the trans cooler hoses) and make sure it is on or just below the "FULL" line when hot.

I know if you have too much or too little in there it can do what you are describing.

no its matic J, DONT put matic S in it!!!! it will destroy your transmission.

Nup, Matic S is the synthetic replacement for Matic J (which is a semi-synth) and will be fine for our transmissions.

It's Matic D (or Dextron III) you can't put in there

What colour is it if is isn't red???

What was used in it and whom did the service?

I'd drop a little out of it (unhook one of the trans cooler hoses) and make sure it is on or just below the "FULL" line when hot.

I know if you have too much or too little in there it can do what you are describing.

Nup, Matic S is the synthetic replacement for Matic J (which is a semi-synth) and will be fine for our transmissions.

It's Matic D (or Dextron III) you can't put in there

not going against what your saying, but ive been tod by ALOT of trans auto joints that its not bad to overfill by a little, and that a lot of trans joints actually overfill

not going against what your saying, but ive been tod by ALOT of trans auto joints that its not bad to overfill by a little, and that a lot of trans joints actually overfill

Isnt that when cold though? And just below the line when hot = just above the line cold?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...