Jump to content
SAU Community

Recommended Posts

pros and cons of club rego. kgo

It's cheap. That's good.

You need to be a member of a recognized club. That's bad.

It's cheap. That's good.

You can only drive your car 90 days per year. That's bad.

It's cheap. That's good.

You have to have a club number plate and cant have any custom hektik combinationz. That's bad.

Yeah log books. If you get pulled over and you haven't filled out your log book detailing the trip that day, it's the same as driving unregistered and you get reamed by the 'long arm' of the law.

Not to mention weekends you won't drive it, so you can save up some weekdays with that. However...if you drive between 11pm and 1am...I'm guessing this counts as two days?!

It's cheap. That's good.

You need to be a member of a recognized club. That's bad.

It's cheap. That's good.

You can only drive your car 90 days per year. That's bad.

It's cheap. That's good.

You have to have a club number plate and cant have any custom hektik combinationz. That's bad.

The car has to be 25 years old. That's bad

used to be just club events and you had to have all the doco for that, became too hard.

it's now 90 days and you have to fill the book in prior to departing as above no book unrego.

car still has to be RWC.

car has to be more than 25 years old

thee is a very limited number of clubs that you can be a member of and you have to go though them to get it,

not like cams where if you are a member your are automatically eligible.

So if you have an old car you hardly drive then it all good.

but as a rule they make it a pain to discourage you, and you only save a couple hundred a year.

I looked at it for the stang but decided full rego was easier.

I thought club rego meant you can only go to events and stuff not just run down the shops

I used to think so too but then I've seen heaps of cars getting around with em on weekdays. I think it's permits from Vicroads that allow you to visit events only.

So if you have an old car you hardly drive then it all good.

but as a rule they make it a pain to discourage you, and you only save a couple hundred a year.

130 for a year.. that's about 500

Are club rego transferable to new owner if you're selling a car with one?

No

It's cheap. That's good.

You need to be a member of a recognized club. That's bad.

It's cheap. That's good.

You can only drive your car 90 days per year. That's bad.

It's cheap. That's good.

You have to have a club number plate and cant have any custom hektik combinationz. That's bad.

Oh another

Easier to get mods allowed. That's good.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
×
×
  • Create New...