Jump to content
SAU Community

Recommended Posts

Useless once again. Be a good lad and find the location for it.

I don't understand why someone would "bypass" a ground cable...

That would make all your electrics run like shit if the chassis doesn't have a strong link to the neg battery

The Iacv valve? I cleaned it last week and have my old gasket. Not ripped, just a bit dirty. Got it from Nissan for 5bux. Nissan ferntree gully has them in stock. Else if yu feel like driving to Dandenong for a second hand one lol

ill have a look when i go to the shop later, also found a gasket. shell be right :)

lolwut

Super moto / motard / retard

8100_328688733877059_1258100066_n.jpg

lol yes I heard a DRZ buzzing around the tennis courts today :)

hehe.. couldn't find the entrance to the court unfortunately, would people get mad if i ripped a skid?

Super moto / motard / retard

8100_328688733877059_1258100066_n.jpg

hehe.. couldn't find the entrance to the court unfortunately, would people get mad if i ripped a skid?

the wheelie has perked my interest.

is it as simple as a pushbike wheelie? put on power, lean back and modulate power + brakes?

hehe.. couldn't find the entrance to the court unfortunately, would people get mad if i ripped a skid?

Where my car was parked, there's a gate that would stop cars getting in, but you could get a bike past it easy. Then walk/ride past the childcare/kindergarten place and there are the tennis courts. Doubt people would even see you, it's usually pretty empty. Plenty of grass though :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...