Jump to content
SAU Community

Recommended Posts

Yeah got him on the case already, his response time is amazing, already got a price lol and I emailed him about 10 minutes ago

He is cheapest that I've used, cause less overheads. Yeah his response time is awesome fast, especially considering how many people buy through him

Day off!

Yessss

I scored one as well, hopefully tomorrow too :P

He is cheapest that I've used, cause less overheads. Yeah his response time is awesome fast, especially considering how many people buy through him

I scored one as well, hopefully tomorrow too :P

I would like tomorrow off aswell. Waste though.. Can't do anything in this heat

Haha stalker. Where you there?

Bought a PVC cap to plug up the intake pipe for a boost leak test :P

lol guess you didn't notice the SAU card I left in your drivers door then

Also day off for me today. Just had to skip some lectures ;).

Woke up excited for Top Gear ep... hadn't finished downloading. Extremely disappointing dl speed dunno what happened. Torrent had good ratios too... Oh well, no matter. Will be done by the time I come home from gym :D.

I would like tomorrow off aswell. Waste though.. Can't do anything in this heat

Worst working outside at the cemetery, no shade heat reflects off all the monuments and stone gets super hot, literally burn yourself it gets that much heat soak

Hey sKids.

Hey man, hows QLD?

Worst working outside at the cemetery, no shade heat reflects off all the monuments and stone gets super hot, literally burn yourself it gets that much heat soak

Hey man, hows QLD?

I'm guessing the sun is dead hot in the cemetery...

QLD is pretty good. Awesome weather over the weekend for once. It has been 3 weeks of solid rain.

why are 300zx's so cheap is it coz no one wants to work on them?

would it be best to go with N/A or TT assuming everything is/will remian stock standard?

300's are so cheap due to the engine having to come out for an oil change.

Flying up to wagga dem Rex planes so small don't trust them

You'll be right, don't worry your pretty little head out.

Oh and afternoon everyone.

Rimon, you're wanting a engine out thing now? Whatever happened to small 4x4 you wanted before?

300's are so cheap due to the engine having to come out for an oil change.

find that hard to believe...

Rimon, you're wanting a engine out thing now? Whatever happened to small 4x4 you wanted before?

need a cheap get around wouldnt mind if it had some style still looking for a decent 4x4 most are either just scrap or dreamer prices.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...