Jump to content
SAU Community

Vic Wasteland Thread

R31Nismoid

By R31Nismoid,
in Victoria

 Share

Recommended Posts

  • Replies 84.1k
  • Created
  • Last Reply

Top Posters In This Topic

  • Birds

    7929

  • joeyjoejoejuniorshabadoo

    6791

  • Sunkist

    6123

  • UNR33L

    4177

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

joeyjoejoejuniorshabadoo
joeyjoejoejuniorshabadoo

probably worth more than your D1R's

Mohsen
Mohsen

i kinda want one. name him al pacacino.

Birds
Birds

You laugh now, but when I'm at a formal occasion with a shitty DJ and they need someone to drop Dre beats...I have something up my sleeve.

Posted Images

Odium Grand Master

Odium

Posted
Posted

SO car was written off but not put o the register..seems strange.

Repairable Write off...

Cheaper for just car insurance to do a write off payout than fix it (properly).

Thus why this sale is clearly dodgy, there won't be a lot of change from $9,000 o.n.o. if it was fixed properly.

Count Grantleyish Grand Master

Count Grantleyish

Posted
Posted

SO car was written off but not put o the register..seems strange.

I think it doesn't have to be on the register if the car's over 15 year old?

That could explain why it isn't on the register...

Odium Grand Master

Odium

Posted
Posted

WOOOOOOTTTTT MY CAR IS READY!

Time to go to the panel beaters and pick it up... Need to get there in under 50 minutes or the place will be shut... Waiting on a taxi to arrive now *impatient*

Odium Grand Master

Odium

Posted
Posted

I've already called him saying I'm interested... Waiting on a call back... Will go and see it on my way home if I can.

Called him again just before... I'm going to go see it tomorrow... with Matt...

Shall record the encounter for the wasteland lulz

Odium Grand Master

Odium

Posted
Posted

WOOOOOOTTTTT MY CAR IS READY!

Time to go to the panel beaters and pick it up... Need to get there in under 50 minutes or the place will be shut... Waiting on a taxi to arrive now *impatient*

So... my car had a camry reverse into the middle of the passenger door.

It went into the AAMI assessment center on Tuesday Morning last week (19th)

It was getting a new door, and bring resprayed at a place Monash Car Center on Princess Hwy

I get the phone call that it ready to come pick up tonight.

Went there to go pick it up and it all looked good. the paint colors matched and all was well.

Car was locked, so couldn't open the door.

Accepted the car, drove it home and on the way I noticed a "few" issues.

They've swapped the inner door panel, speakers, glass, etc into the new door. The tint on the glass is scratched quite badly and is peeling (like inch long sections peeling off)

The power mirror does not function at all.

The power window functions intermittently, I'm thinking a wiring connection issue.

The panel gaps are different from the top to the bottom of the door, it varies by more than 2mm from top to bottom.

Letting the door swing shut by itself, it stops with 10cm to go.

Once fully closed, the top of the window looks to be about 1cm lower than it should be, so it doesn't go into the slot where it should go, instead it hits the bottom of the fat rubber bit.

Honestly, how the f**k can a place f**k it up so much... *sigh*

Gonna call JCI tomorrow and rip a new arsehole out of this joint.

alr33x Grand Master

alr33x

Posted
Posted (edited)

2mm panel gap on a 15~ year old car...uhoh lol

Who could even notice 2mm other stuff sounds fair enough though. Panel beaters would have given zero fks they are useless pricks

Edited by alr33x
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...