Jump to content
SAU Community

Recommended Posts

Vw is far from prestige. Euro maybe? But does not come close to prestige.

They're seriously shit. Sitting their reving their engines like heroes. One of the r36 was doing it with chunks of blue smoke. People were clapping saying its awesome. Wut?

Precisely, but everyone who owns one thinks that they've got themselves a good european car(owing to the fact that VW group owns audi as well so their engines have some similarities) compared to all the other "inferior" japanese "cheaply" made garbage. The look on their faces when you tell them you own a skyline says it all.

Vw's have become the affordable european car and in general people tend to associate a "prestige value" with euro vehicles.

Yeah and they get it apr tuned and lean the shit out of the car to get more power, thinking that it's "hidden" potential only to end up with a ticking time bomb. I love it when they always say "My fuel economy has improved after the tune and I get loads more power! Awesome!"

Hmm had imports most my life and still do, love them to bits. Also have a vw gti infront of my house and I can't exactly see how it's shit or cheaply made. It's far from prestige but it ain't shit either.

And dude the apr tune just leaning the shit out of it to make power. I can see the hatred and all but come on!!!

Hmm had imports most my life and still do, love them to bits. Also have a vw gti infront of my house and I can't exactly see how it's shit or cheaply made. It's far from prestige but it ain't shit either.

And dude the apr tune just leaning the shit out of it to make power. I can see the hatred and all but come on!!!

friend wasnt saying they are shit, he was saying that the engineers do a great job of making cheap components feel nicer/more expensive than they are, but at the end of the day, they are still cheap materials.

friend wasnt saying they are shit, he was saying that the engineers do a great job of making cheap components feel nicer/more expensive than they are, but at the end of the day, they are still cheap materials.

Of course, what manufacturer isn't trying to save money and use cheaper materials, they all do it!! I wasn't aiming my comment directly at you anyway.

Hmm had imports most my life and still do, love them to bits. Also have a vw gti infront of my house and I can't exactly see how it's shit or cheaply made. It's far from prestige but it ain't shit either.

And dude the apr tune just leaning the shit out of it to make power. I can see the hatred and all but come on!!!

The problem is individuals owning a VW as far as those whom I know love to stick their noses in the air and associate it as a "prestige" and therefore better which is generally not the case. In addition to the tuning etc. made to the engine and thinking that they have superior performance/reliability as opposed to japanese cars, assuming that you're not trashing the shit out of your jap car.

Regarding the leaning out thing, it's because they made it readily available and marketed it and made it mainstream, people don't realise the harm they are doing to their cars and take them to a VW service centre which are probably going to use sub-par oils/fluids that are not made for the increase in power obtained from the aggressive tune, not to forget, stock internals.

Anything above 227 hp (not much room to play with) from a stock GTI engine is going to cause problems, APR stage 1 gets you 254 hp, way above the limit for the stock engine. The Audi TTS which has 265 hp has the same 2.0L I4 engine reinforced from factory, if the engineers from Audi thinks that a reinforced engine is required to take that sort of horsepower, what makes you think that APR's claims that they are tuning it within the limits of a stock GTI engine without any reinforcements are true? Furthermore, every 2.0L i4 engine from VW that produces more or equal to 169kw's of power comes with reinforcements made to the internals. I think their engineers know what's good for their own engines and what isn't.

4th paragraph from: http://www.caranddriver.com/reviews/2010-audi-tts-road-test-review highlights the reinforcement of the engine internals from the 2.0L i4 engine to accommodate the increase in power from the tune/turbo upgrade.

But meh, at the end of the day, I just hate it when people judge you for driving a japanese car when they drive a european one. It's not the car, just the driver's that reek of elitism that annoys me :P , and my advice to any potential/current GTI owners, please just keep the engine stock or face reliability issues down the road, unless you're going to reinforce the internals :thumbsup: then go crazy!! :banana:

Edit:

jelly? golf the new civic? :P

SAU has been in people's faces a lot this year I think. not surprising people see what the fuss is

Yes it is xD polo's too are pretty affordable hatches too nowadays (plus it's european :rofl2:) , good for transporting stuff around :yes:

Edited by arcenite
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...