Jump to content
SAU Community

Recommended Posts

Adding to the VicRoads rip off saga...

Just replaced spark plugs in car...it runs 63 times better...10,000km is too long for copper plugs in a modified car methinks. Though that interval was more out of procrastination.

The only reason I let mine stretch to 10,000km sometimes is because of the bloody RB crossover pipe and not wanting to scratch up my pretty valley cover paint if I don't remove it (+20 minutes) to the job.

I remember my old ford laser... Pop off the leads, unscrew plugs, screw new plugs in, cry because you drive a ford... Finished in 5 minutes

That awkward moment when your housemate receives a letter in the mail from the Australian Federal Police.

those guys hardly deal with misdemeanors or misunderstandings. I wonder if it also deals with Immigration issues, or would the Department Of Immigration just deal with it? maybe terrorism or illegal visa. hmmmmmmm *curious*

The only reason I let mine stretch to 10,000km sometimes is because of the bloody RB crossover pipe

This

It's a 30 minute job that should be 10 minutes.

And working with old hoses and screws, I'm ultra careful about the way everything goes back.

I leave the valley cover off, so I can do 5 of 6 plugs without touching the pipe. But Nissan Y U put crossover pipe slightly too far over the 4th cylinder? If I had uni-joint sockets I could do it, but don't really like using those unless I have to.

Can't get started, Chemical Heart... Every time I get started, you pull me apart.

Old Grinspoon is the best Grinspoon

dead Grinspoon is the best Grinspoon

Just replaced spark plugs in car...it runs 63 times better...10,000km is too long for copper plugs in a modified car methinks. Though that interval was more out of procrastination.

I ran BCPR7ES gapped to .9 and used to change every 20,000, even when changed they worked fine and looked 100%

dat trent tune

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...