Jump to content
SAU Community

Recommended Posts

R1R 205/45/16. Yup, 4x100 16x7+33

7" bit skinny for your power innit? :P

R1R is so HNNNNNG in the wet. So so good. Picks up so much shit and flings it in the guard though

Got it through streeter, not very often you see this pop up. Haha, its forged too, around 6kg each.

<3 R1R wet times

Wish they were a bit better in the dry though.

this micra is going to be the little car that can, if you go through with all that you're planning. decked out from top to bottom.

inb4 Thule roof racks with single speed ontop and stance.

R1R 205/45/16. Yup, 4x100 16x7+33

7" bit skinny for your power innit? :P

R1R is so HNNNNNG in the wet. So so good. Picks up so much shit and flings it in the guard though

Got it through streeter, not very often you see this pop up. Haha, its forged too, around 6kg each.

Do you have old rims/tyres your going to get rid of?

this micra is going to be the little car that can, if you go through with all that you're planning. decked out from top to bottom.

inb4 Thule roof racks with single speed ontop and stance.

i hate stance.

im all for filling arches with wheel, but if it aint practical, it aint going near it.

roof rack will help to transport gear to track tho!

spent many hours chatting to scotty last night about the way to go, and he has dragged me kicking and screaming from the ghetto cooler piping i wanted..... ive still got my heart set on a jdm exhaust system or at least rear muffler tho...

Do you have old rims/tyres your going to get rid of?

Yes, but they're all sold. And most likely cost a lot more than you're looking to spend. Haha

6kg? fuuuaark. 7" is all im running at the moment. anything bigger is scrub-city.

My te37 15x7+35 was around 4kg.. :P

<3 R1R wet times

Wish they were a bit better in the dry though.

When they're hot they perform awesome. RSR had better grip than these R1R at cold/warm daily temperatures though (dry). But R1R feels crazy when hot.

Can't wait to hit winton now.

Yes, but they're all sold. And most likely cost a lot more than you're looking to spend. Haha

When they're hot they perform awesome. RSR had better grip than these R1R at cold/warm daily temperatures though (dry). But R1R feels crazy when hot.

Can't wait to hit winton now.

Touche'

I need to get new tyres but figured some of the rims on "JDM rims for sale" you can get a set of rims and semi decent tyres for not much more

See you soon at winton brah

You're spending money on a micra? Can I ask why?

I saw a little toyota starlet the other day at Trent's pushing 190kw, he was going in for an ethanol tune.

There is no way you would expect to get thrashed by a micro car, with a baby on board sticker on the window. I'm all for it. :)

really? :unsure:

my 16x7 +33 is like 8kg without tyres and 14-16kg with.

Pretty sure it was 4kg without tyre.

Touche'

I need to get new tyres but figured some of the rims on "JDM rims for sale" you can get a set of rims and semi decent tyres for not much more

See you soon at winton brah

Haha yep. 2nd hand usually better.

When's sau winton day? Going tampered on 10th, I wanna beat my 53, especially when the 53 was my last lap of the day, and the car still had more in it. Gonna have even more in it now due to tyres.

I saw a little toyota starlet the other day at Trent's pushing 190kw, he was going in for an ethanol tune.

There is no way you would expect to get thrashed by a micro car, with a baby on board sticker on the window. I'm all for it. :)

Dezz doesn't like anything.

If dezz was a word in the dictionary, it's meaning would be; "He who hates the world and all it possesses"

Dezz doesn't like anything.

If dezz was a word in the dictionary, it's meaning would be; "He who hates the world and all it possesses"

maybe Hamish and Dezz should partner up and fight crime or something

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...