Jump to content
SAU Community

Recommended Posts

send me resume.

only draw back in only area that might be hiring ATM, is full of Asian females..so you might have to get daddy to buy you a brand name bag to fit it.

Sounds attractive to me, might need to send you a PM too so then Alvin and I can go man bag shopping.

i know of one tuner whos notorious for bad cold starts on eth.....

so might not be plugs dude.....

My car was tuned on a 30 degree day so I doubt the cold start is any good. Plus the copper plugs have been in there for 3 years now so I might swap them out and see how I go.

15 goes at starting is the worst it has ever been. Usually starts after 2 or 3.

  • Like 1

I've got about 6 wooden pallets sitting here in Cheltenham that are about to go to the tip, and 6 black plastic but they won't be much use...

If you want to travel, come take them ;)

Is Artz new jerb near you? He has a ute... :P

Otherwise, I can't fit too many pallets in the stagea, and not even a chair in the back of the evo. lol.

Anyone selling 4-stud of PCD 4x100 wheels? The missus's Civic could do with some new shoes.

just sold my spare, spare set.

be prep'd for a shock. you can get decent 17's with good tyres in any other sp, for less than 14's in 4x100,

f**king honda fags have killed it.

i got some bmw bottle caps in the garage with bf goodrich semi slicks, brand new too lol.

just sold my spare, spare set.

be prep'd for a shock. you can get decent 17's with good tyres in any other sp, for less than 14's in 4x100,

f**king honda fags have killed it.

i got some bmw bottle caps in the garage with bf goodrich semi slicks, brand new too lol.

Shiiiiiiiiiiit. Not chasing anything special, just something better than the factory 14" steel wheels :(

Anyone?

14 inch tyres are a nightmare to find anything decent in, so maybe look for 15s? have a look on gummers?!?

Nah, not looking for any size in particular. She's keen on any wheels that are bigger than the stock 14", so open to 15s, 16s and 17s.

Had a look on gumtree and full of friggin' dreamers who think their Bob Jane specials are worth as much as genuine forged japper rims. Cocks.

told ya. 4x100 is a kent........ and most are ugly as f**k too. i stuck with bigger oem wheels, maybe look at the bigger hondas, see if there is anything cheap?!

Yeah I know. Worst aprt is, the missus brought a set of matte black 4x100 rims in a tough offset and look mint (look almost like TE37s) but the offset was too aggressive for her as she didn't want camber of anything like that, so looking to sell them or trade them :(

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...