Jump to content
SAU Community

Crashed Stagea In Melbourne

Aaron S

By Aaron S,
in Four Door Family & Wagoneers

 Share

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

iamhe77 Grand Master

iamhe77

Posted
Posted

Yep, that was mine.

Hmm, 750 bucks currently for a leather interior, popup screen, reversing camera and Nismo exhaust which are all in good condition.

Turbo, intake, dump may be okay, but I don't know.

Steering looks fine!!

Oh, and that headlight was fine Alex :P The other one, well that was in a million bits... instantly. Can't believe how readily they disintegrate!

Scott, and what radiator cap to you have Mr. Mishimoto?

Should've grabbed that damn G35 battery cover pinch.gif

iamhe77 Grand Master

iamhe77

Posted
Posted

Quick search for "battery cover" brings up this Paul whistling.gif

http://www.skylinesa..._1#entry5148591

Any Nissan/Infinity dealer in the US, I went through West Covina Nissan for mine, but they are not so cooperative since Tony left.

Might even be some on Ebay Motors.

Should be a bit cheaper now though, I believe my mate got his recently for around the $100 but really needs to make up a couple of brackets.

iamhe77 Grand Master

iamhe77

Posted
Posted

How much factory bodywork did you need to cut? Any pics?

looks a lot neater with that cover.

Cheers

Yep, looks waaay nicer with one.

If you look at yours, you will see that there is an extra 10-15mm(?) of metal above the square rubber grommets for your hoses.

Cut that in line with the top of the grommets and run a brush with some rust prohibitive paint, then all you need to do is make up a small bracket for the top right section of the cover and cut a little in that area to fit :)

Surely they have some stupid hidden reserve for like 6k?

Yep, I was told they had $6k on it.

bigkevracer Grand Master

bigkevracer

Posted
Posted

Yep, looks waaay nicer with one.

If you look at yours, you will see that there is an extra 10-15mm(?) of metal above the square rubber grommets for your hoses.

Cut that in line with the top of the grommets and run a brush with some rust prohibitive paint, then all you need to do is make up a small bracket for the top right section of the cover and cut a little in that area to fit :)

You can't cut the plastic cover?

I'm somewhat interested, but I can't find the run through from last time you did the group buy - am I just not searching properly? It's not on here or the 'somewhat awesome' forum as far as I can tell?

iamhe77 Grand Master

iamhe77

Posted
Posted

You can't cut the plastic cover?

I'm somewhat interested, but I can't find the run through from last time you did the group buy - am I just not searching properly? It's not on here or the 'somewhat awesome' forum as far as I can tell?

You won't find one.

GB didn't go ahead and it was only after I installed mine that I thought of offering the GB.

I think you can cut the plastic cover, but I couldn't see doing so would end up with a satisfactory finish so I cut the top strip of metal instead.

No need to worry Ryan, it is not a big job.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
×
×
  • Create New...