Jump to content
SAU Community

Recommended Posts

I thought we were looking for milky residue..

A milky residue will only tell you the oil isn't getting up to temp, common with short trips, low temp thermostats and winter weather.

Here is an interesting read I found about oil thicknesses, not related to e85, just in general.

http://www.evolutionoz.net/forums/index.php?showtopic=87122

  • 2 weeks later...

hey guys just asking for advice today take the litte girl for a spin for 20 minutes around the block i have just put in castrol edge 10-60 for the first time when i pulling out the dip stick i can just see abit milky oil in the back of the dip stick the car gets used once a week if that is this alarm bells (head gasket) the oil has done less then 100 km after dyno tune thanks joe

Edited by gtr0321994
  • 2 weeks later...

I am tempted to throw some HPR diesel 5 in mine just cause I have half a bottle there and im poor atm...its ci-4/SL rated....not sure if good idea or not

Did a fair bit if research on BTOG. Seem diesel seems to coping with contaminants on their oil analysis. But again the consensus is the more you drive the car the less it contaminates. Same as what guys have been saying here. Diesel is generally cheaper too...$50-80 for 10 litres.

HPR diesel is a very good oil. Spoke to a guy at autobarn a while back that used to work for them and do a lot of r&d, was in their for ages chatting about oil. He made some really interesting points about oil in general. One that really made sense was that if you change your oil every 3 to 5 thousand km then full synthetic is a waste of time and that they are really designed for extended oil changes. On all the testing they did with all the oils and brands, diesel oil stood out in most areas of the testing. Interesting. But again for oil changes longer than 5000km on high performance cars synthetic is where it is.

on E85 oil has to be changed more frequent so the advantages of full synthetic is irrelevant and that's where diesel oils come into their own with the high zinc and cleaning properties. Anyway thought I would share.

I used to use Royal purple, then went AMSoil, now I'm with Shell Rotella. 5-40 or 10-40. Seems ok. but I'm only at 15% Ethanol

BTOG raves about Rotella. A lot of oil analysis done in their threads. Interesting to see what your feedback is if you keep using it. Keep us updated.

There is oxygen in some of this . Diesels are often low revving high torque engines for their capacity so it stands to reason that you can't use eco Nazi grade oil in them . Getting late emissions compliant petrol engines to survive on green oil was all about valve train changes because this area is where you get the highest point loadings in a petrol engine . Things like roller rockers and roller cam followers in pushrod engines were done specifically to make valve trains survive on green I love cat converters "oil" .

Because diesel engines have high bearing loads at low speeds the oil has to be able to form and maintain a reliable film to stop components eating each other . Because the eco Nazis are attacking diesel emissions of late you can expect them to change as well .

Take it to the grave , eco oil is about cat life in petrol engines end of story . Because the Nazis do emissions tests I believe yearly in the States they're changing cats and probes more often than we do .

Now synthetic oil , the properties good ones have are more than just living longer than dino oils . Flowing better at lower temps has nothing to do with longevity nor standing up to higher temps . If your engine runs clean and doesn't contaminate it's oil then yes it can live longer but if it doesn't then the only way to ditch these contaminants is to ditch the oil .

I like some diesel oils because to get the good anti wear additives at a sane price it's hard to go past them . Synthetics are creeping in to them and that's not a bad thing either . I run Rotella T6 5W40 and have no problems with it .

A .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That was the first session so not a lot to take from the day. It was low 20s ambient and the coolant had got to 110 (and obviously had some pressure!) so that still needs to be addressed. I haven't downloaded the data yet but will. I had refilled the auto trans with Redline DT6 because it claimed the best viscosity I could find at 100o. It wasn't really long enough to get a good feel for that; while the trans got to 100o in the session it still wasn't shifting crisply as I hoped. I think I'll try a few more sessions before judging. No steering motor overheat but I'd hope not in only 1 session! But finally the suspension; it was night and day over the standard stuff and the car was a couple of seconds quicker on the same crappy tyres, which is a huge difference. I'll stick with that and get some sway bars and a mechanical diff sorted too and see how that all goes together
    • I guess it’s partially a compromise of how my car is used, wanting to be able to switch from drift to grip with track side on-car adjustment. Also partially with the way the knuckles are set there is more static camber but less dynamic camber gain. 
    • OK, so update from the track day on Friday It was a classic "an unfortunate series of events'. There were a few cars around and when i checked my mirror coming out of the fish hook I notice some smoke from the rear of mine. Looked again and it was getting much worse, I figured I'd blown a turbo or something to got off it and pulled off the racing line. However.... since it is a left hairpin into a right kink, I was on the inside of the next corner. There was a car passing me on the left and a big drop off over the ripple strip on the right......and someone had knocked the witch's hat that was on the apex about 1m onto the track. So, between those 3, I decided to mow down the cone and not damage my car/the other car. Right choice, but surprising result.  The car decided the cone was a small pedestrian so it blew the rear bonnet hinges up to protect their head in the upcoming person to car impact....I didn't see that coming and like an airbag deployment it happened super fast. Straight into the pits from there, everything was driving fine but it became clear it was a coolant leak not smoke, it was billowing up onto the windscreen. Onto the trailer and home. I'll do a separate thread about the repair (once I work out what it is ), but the immediate problem was the bonnet wouldn't open because the front was pinched onto the front bar and would not release. Ultimately we unbolted the hinge from the bonnet, pulled it back a little and it released from the front OK. "There's your problem", the top radiator hose had popped off at the radiator.
    • Yeah that looks like great caster, but I'd suggest trying less front camber some time and seeing if it helps with braking without reducing mid corner speed too much
    • I ended up setting the rear 5mm higher than normal to give some clearance.  My plan is to run the least camber I can in the rear which I think with the extra width is going to need to be -1.75 to -2.00° just to get clearance.  Guards have been rolled and pulled as much as they can/I would be wanting to.  front has the Acostal knuckle with the KPI change and the drop etc. So should be okay with the existing settings I have run with AR1s etc Front: Toe total -2mm(1mm out each side) Caster +7.5° Camber -3.8° Ackerman +15°
×
×
  • Create New...