Jump to content
SAU Community

Recommended Posts

put my stock cat and factory cat back on and went to campbelltown on tuesday to clear my exhaust, i failed as it registered 96db...with the stock exhaust !!!

dunno how this can be but im about to take the exhaust to a shop to get a big muffler put in

The ADM R32 GT-R's got a different rear muffler for exactly that reason. I thought it was a bit strange and to be honest I can't pick the difference between my ADM or JDM ........ they sound the same to me.

Bob.

  • Replies 219
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yeh

At the defect area the EPA were there Testing exhausts for noise with mic's

And snooping under the bonnet to make sure all the charcoal canisters are connected, no bovs or atmo catch cans, etc etc

Also checking window tint, thankgod mine is 35% and all the other usual crap

One guy asked if I had my bucket seats engineered, told him to check the other gtr over there cos they are factory !

As for loud exhausts, to flow huge power and be quiet it's going to need to be a custom job. Custom = expensive, which is why hardly anyone goes down that path.

custom isn't necessarily expensive. It depends on if you let someone rip you a new one, or go quality. My system fully fitted cost me less than it should have, but turbo back, custom built mufflers, and a new metal cat should have cost me $1500. I don't think that's overly expensive. Yes more then a "I'll take a noisy ass 3" for $300 thanks!"

Anyone who heard my old 2530 can attest to the fact that it was very quiet for what was in front of it. A verydeep but not loud note at idle and as it came past 3000rpm you could hear the motor louder then the exhaust... Rare in a turbo car.

custom isn't necessarily expensive. It depends on if you let someone rip you a new one, or go quality. My system fully fitted cost me less than it should have, but turbo back, custom built mufflers, and a new metal cat should have cost me $1500. I don't think that's overly expensive. Yes more then a "I'll take a noisy ass 3" for $300 thanks!"

Anyone who heard my old 2530 can attest to the fact that it was very quiet for what was in front of it. A verydeep but not loud note at idle and as it came past 3000rpm you could hear the motor louder then the exhaust... Rare in a turbo car.

were was said muffler aquired

  • 5 months later...

Ill say one thing it's the drivers fault. The car mods have nothing to do with it. It's just plain stupid, this has to stop who ever rights the rules is a complete idiot with no brains. A Speeding driver is a speeding driver. There gonna speed in any car, and they should not be tighting up any engineering rules if a engineer says its safe to be on the road so be it.

upto the cop that decides to pulls you over.......if they want to defect you they will and they will do it however they like....

in my case the cop full lied about what was on my car and i only found that out once i obtained the details from the SDRO (ie the actuall hand written report from himself) and fined me for not meeting as per the engineers report etc etc

the story goes on but gives you an idea.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It's almost certainly a reluctor generating an "AC" waveform. No, ECUs don't generally read those - they're usually set up for PWM square wave 0-5v stuff.
    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
×
×
  • Create New...