Jump to content
SAU Community

Recommended Posts

Fuel doesn't have any idea how many cylinders the combustion chamber its being squirted into is joined up to ;)

Ultimately the harder the work the fuel has to do, the more E85 comes into its own... but you can still definitely get gains. I've seen from 3-7% from E85 on a naturally aspirated engine, depending on a variety of things. The most magical results I've seen are on highish compression turbo setups running a bunch of boost though.

With a relatively stock V8 I'd say the extra fuel usage would outweigh the gains, unless you have exhausted all alternatives and not worried about the ~35% extra fuel usage - and the fuel system upgrade you are likely to need to do to support that fuel usage.

If you were going to drop a decent turbo or two into the mix then E85 very quickly starts coming into its own.

Link to comment
https://www.sau.com.au/forums/topic/400917-e85-fuel-on-v8/#findComment-6368986
Share on other sites

Any engine tuned to run on E85 will see some power benefits, but these benefits are much more obvious with engines that are prone to detonation or high heat, as high octane and reduced temperatures are the mainstay advantages of E85 over unleaded. Thus forced induction engines benefit greatest from it, but there's no reason you can't advance the hell out of the timing on an N/A V8 and see some good gains there.

Link to comment
https://www.sau.com.au/forums/topic/400917-e85-fuel-on-v8/#findComment-6368996
Share on other sites

6% is still 6% , is that throughout the revrange or just a top end figure..I was thinking e85 could help gain some midrange..

My missus has a 3L Accord. its a zippy tank. but unfortunatly there isnt alot that can be done with it as the auto box is subject to failure even in stock form.

I think the comp ratio is 10.1, Now I read a thread where a guy just filled his up with E85 ,with stock everything and no additional tuning he was pulling at least a car length on a similar car on pulp..he ran it for a while with no issues but finally saw reason that it might not be the greatest idea without a proper tune

I have been very tempted to get an emanage or something, open up the exhaust a little and just tune for e85 to see what gain could be had..A 10% top end at absolute best, would be all I would expect, but more importantly I am interested in the low to midrange gain it could have as that is where it gets driven most..

i have been running it on e10 for ages without issue and getting great fuel economy as well, almost equal to BP98.

There will be little gain with stock compression. Chuck some 13:1 comp pistons in and it'll be a whole different story!

And biannual headgasket replacements...lol ..this was always the best way to make a V8 (or any NA for that matter) move anyway

Link to comment
https://www.sau.com.au/forums/topic/400917-e85-fuel-on-v8/#findComment-6371367
Share on other sites

Well all you really need is a bigger pump and maybe a bit of extra pressure should work to some extent..At worst you get bigger injectors...

But i see where your going, Injectors,pump,piggyback,your looking at least 2000$ for for only a 5-10% increase...

Though if you already have these mods in place you have nothing to lose..and plenty of people have spent more for less

Link to comment
https://www.sau.com.au/forums/topic/400917-e85-fuel-on-v8/#findComment-6371658
Share on other sites

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...