Jump to content
SAU Community

Recommended Posts

Ok i have decided to put together a tutorial for installing new discs. i thought this might help a few people, so they dont make the same mistakes I once did.

Step one:

Once you have safely jacked the car up and removed the wheel, pull out the brake pads. If unsure about this, Click here , for brake pad replacement/removal tutorial.

Step two:

Find the two caliper bolts at the rear of the caliper (see pic.)

DSCN4505.jpg

You may need a fairly long breaker bar to initially loosen the bolts as they are very tight. When you have removed the caliper from the mount be sure to rest it on a bench, on a suspension link (as in the picture) or just tie it up with string. It is important not to twist bend or hang the caliper by the brake line as it may damage the line.

DSCN4493.jpg

Step three:

For the front disc it should easily slide off the hub.

For the rear disc it may be a little more difficult, sometimes fusing to the hub or the handbrake (drum brake inside disc) holding it in position.

Note: make sure the Handbrake is OFF or you will not be able to pull the disc off.

Using the threaded holes here screw in two bolts (M8x1.25) into the hole.

DSCN4485.jpg

You will find they push the disc off the hub. After the initial bolt push the disc should simply slide off the hub and drum brake.

It should look like this:

DSCN4495.jpg

Step Four:

Ensure you clean the new disc's braking surface with brake cleaner or paint thinner to remove the anti-rust lubricant the manufacturer applies for storage. This lubricant can contaminate pads and seriously effect braking.

Step Five:

Simply slide the new disc over the hub and into position.

Remember to fit rubber plug on the new disc. If your new disc didn’t come with one, just use the one from the old disc.

DSCN4500.jpg

DSCN4501.jpg

Step Six:

Gently slide the caliper back into position and tighten caliper bolts. (according to the R32 GTR manual 92-118Nm)

Step Seven:

slide brake pads back into position. Fit pins and clips. Sit in drivers seat and pump the brakes a few times until it feels firm again. Fit the wheel back on, and you are done!

I hope this helps a few people.

Ben.

Link to comment
https://www.sau.com.au/forums/topic/40346-brake-rotor-disc-installation/
Share on other sites

  • 1 year later...

Thanks for this one !

Did my fronts (well one of em) yesterday using this tutorial.

Just thought I'd add one extra pic.

I did my fronts on the R33 GTS-T and found a couple of extra bolts to undo so you don't hurt you're brake line. (See piccie)

Pretty obvious what I mean, and they're not hard to undo...compared to those bugga caliper bolts !

THanks Bbenny!!! :)

post-5823-1134078508.jpg

  • 2 weeks later...

I request this thread be stickied.

Good on you Birnie for finding it dude. I wish I had searched for it two weeks ago :(

Adjusting hand brake

If you are removing your discs it is probably a great time to check your handbrake. The R32 manual says to to:

Place the disc on the studs and fit wheel nuts so disc is secured to the hub.

(Give the adjuster a good blast with brakekleen)

Turn the adjuster from the top and towards the vehicle. ie. you are pushing the screwdriver into the top and it will click as it rotates away from you.

Once the disc is locked and immobilised, rotate the adjuster in the reverse direction for five or six clicks. I went with six as I would hate to have that drum rubbing

Replace the rubber plug and you're done.

You can then adjust the lever stroke with the nut under the handbrake in the centre console. It should fully engage in 6-8 clicks.

adjusting_handbrake.JPG

Cheers!

  • 9 months later...

should also be noted that if you are going to use old pads with new rotors, the pads should be faced so that they wear evenly on the rotor. it is best to put new pads and rotors on at the same time.

and they would probably need bedding in.

another tip to remember is make sure the hub and rotor surfaces are clean before you put the rotor back on. any grit, flakes of rust or any of that sort of shit between the rotor and the hub will give you runout and shudder problems in a short period of time.

  • 9 months later...
  • 3 months later...

Just a note on Handbrake adjusting I always find when i adjust a handbrake i slack off the handbrake end eg the end connected to the handbrake lever inside the car before adjusting it at the rears just something to think about really basically slack the lever end off then adjust the shoes out at the rear to the required amount then check for 6 clicks at the lever if not loosen or tighten until 6 clicks then it should all be setup correctly without rubbing on the drums etc :nyaanyaa:

  • 11 months later...

Is the whole 6 clicks thing a Nissan recommendation or just a forum thing?

I got my R33 with fairly low km (48,000) and at 58,000 now, my handbrake is tight on the 4th, bites on the 2nd, and generally holds on steep hills on the 3rd!

Is that a low km thing or adjusted different? As i have checked the clearance and it certainly doesnt rub when the handbrake is off.

Is the whole 6 clicks thing a Nissan recommendation or just a forum thing?

I got my R33 with fairly low km (48,000) and at 58,000 now, my handbrake is tight on the 4th, bites on the 2nd, and generally holds on steep hills on the 3rd!

Is that a low km thing or adjusted different? As i have checked the clearance and it certainly doesnt rub when the handbrake is off.

If it doesn't rub, you're all set. IIRC 6 to 8 clicks is what's in the workshop manual.

when replacing a rotor, although it is recomended, do you actually need to replace rotors on both sides at the same time? for example i want to replace the front left only, does that mean i have to replace the front right as well?,

If you replace the front left only, you'll probably end up with uneven braking, as one caliper clamps before the other. With the left disc being new (ie. thicker) it'll meet the pad before the other side does. As you keep pressing your foot down to get the right side to clamp, it'll now be pressing harder on the left side, and so on. So you'll prob end up with the car steering left every time you hit the brakes.

It has been a while since I changed the brakes on my R32 but I don't remember there being any way to tighten one caliper in particular. You'd need to be able to offset the pistons, which you might be able to do when you bleed the brakes after changing the disc. Actually no, I don't think you can because you cant adjust individual calipers on a stock car.

Anyway, I highly recommend changing both, but I guess it depends on how worn the right side is. If the thickness is fairly close, you could be in luck. If you REALLY wanted to only change one, you could have the new one machined to reduce its thickness to match the right hand disc.

  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...