Jump to content
SAU Community

Recommended Posts

Iain did say that it made a difference.

Not as significant as the front brace; but it doesn't deal with the same kind of loading either, but he felt it was worthwhile.

I'm getting one. ;)

  • Replies 182
  • Created
  • Last Reply

Top Posters In This Topic

just ask someone who has one right now...i think iamhe77 has one on his, or zel02 who owned the bars previously

I can't really compare it with and without as it came with the rear bar (and a "different" front bar) installed already and I have not been bothered to remove it yet.

I can tell you that it corners much better and flatter than my NM35 which had Nismo suspension (current PM35 has Bilstein struts and stock springs).

OK for those that have said they want to be in this I will be sending you a PM by EOB today. If your in and you do not receive a PM from me please contact me.

Just a heads up guy's....I will not be chasing you on this....if payment is not made by the 1st you wont be on the GB.

Can you please PM me back when payment is made.

Edited by Jetwreck

Done, thanks Craig.

Would I be correct in saying that delivery date is likely to be minimum 8 weeks from 31 July?

You said 6 weeks for production in the opening post, so I figure a week or so to deliver to Australia, then about a week for them to reach the individual states?

Done, thanks Craig.

Would I be correct in saying that delivery date is likely to be minimum 8 weeks from 31 July?

You said 6 weeks for production in the opening post, so I figure a week or so to deliver to Australia, then about a week for them to reach the individual states?

Sounds about right........give us a couple of days to process payments to OX though.

Sounds about right........give us a couple of days to process payments to OX though.

Will OX be wondering why they are selling heaps of rear braces but no front ones? :whistling:

Hey guys i wont have enough this week to put through but i dont get paid until tue 31st, is that okay or am i out. Because ive got sway pars and links and all i need now is this and daleos front and its done?

Hey guys i wont have enough this week to put through but i dont get paid until tue 31st, is that okay or am i out. Because ive got sway pars and links and all i need now is this and daleos front and its done?

I'll pm you when I get to my laptop...should be ok.

this worth while for v35 coupes? scotty on another note im gonna get a GT3582r 1.06 rear .70ar front housing - using HKS ST 3037 kit, do i need anything special to make it fit?

is this bar a must or do i just get the front ? i got every other handling mod lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...