Jump to content
SAU Community

Recommended Posts

Damn, i thought the newer generation of coolants were environmentally friendly(er) n putting them down the drain wasnt a problem.

Not so the case?

I asked the local Natrad bloke what he does with his waste, he said he treats it (to even out the PH I think) and then dumps it down the drain.

I asked the local Natrad bloke what he does with his waste, he said he treats it (to even out the PH I think) and then dumps it down the drain.

There are many neutral pH substances that should never be dumped in a drain.

The treatments he uses might include (amongst other things) surfactants as well as acid/alkali chemicals I think

just tip it on your weeds....

don't pour it down the drain and do not tip it on your weed...

I just chuck it on the plants...doesn't seem to do them any harm, in fact I noticed that at my parents house the weeds that my father emptied coolant on did better than the neglected adjacent weeds which didn't get a watering.

Lol seems like my "pouring down the toilet" post got deleted.

The only reason i said that is because all sewerage in the City i lived in is processed in a treatment plant before going anywhere near the ocean. The water outlet from it is cleaner than the water its being dumped into. So really its not a bad option. :)

And im pretty sure a treatment plant is well equipped to handle anything that could possibly be flushed down a toilet. They would have had it all and some.

Edited by gotRICE?

If some of you have seen what ends up in the tips, and leaches into the ground, Coolent it the least of your worries - Though im not one to add to the crap land fill.

Check with local council - i know mine has cirtain days per year were they set up a big chemical/paint/oil waste disposal at a local carpark,

They let you bring it all and dispose of it, Best thing it, due to saftey they wont let you out of the car, So pop your boot and they will grab it all out for you :)

Actaully my local council has some good services- Free woodchipping/mulching 5 times per year its great. Free mulch and dont have to take anything to the tip, Just go nuts with the chainsaw and leave it all out the front drive way- Come home to 6-7 bags full of fresh mulch.

Edited by sydking

Lol seems like my "pouring down the toilet" post got deleted.

The only reason i said that is because all sewerage in the City i lived in is processed in a treatment plant before going anywhere near the ocean. The water outlet from it is cleaner than the water its being dumped into. So really its not a bad option. :)

And im pretty sure a treatment plant is well equipped to handle anything that could possibly be flushed down a toilet. They would have had it all and some.

Thats cool!, Our here in sydney goes straight out intot he ocean, Feild of mars even has the old above ground sewage tunnles from many years ago.

And wasent it maroobra beach back in the day that had the sewage pipes leading straight into the beach haha

Lol seems like my "pouring down the toilet" post got deleted.

The only reason i said that is because all sewerage in the City i lived in is processed in a treatment plant before going anywhere near the ocean. The water outlet from it is cleaner than the water its being dumped into. So really its not a bad option. :)

And im pretty sure a treatment plant is well equipped to handle anything that could possibly be flushed down a toilet. They would have had it all and some.

whilte the sewerage processing systems can deal with it, doesnt mean that it easily or prefereably can. For example, the amount of processing that it takes to sort bleach via the sewerage system is huge. But of course most people do use bleach in their toilets n sinks. But, essentially, its bad for the sewerage processing system.

Im sure coolant would also fall into this category.

OK, I've just asked my neighbour Ricky, who has a 80 year old Antique car.

He (Alan) will gladly take that pre-1985 coolant off your hands :)

I can pick it up for him.

Sure man, but its a little bit of a drive to pick up for a bottle of coolant!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...