Jump to content
SAU Community

Recommended Posts

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

carbon fibre bonnet - 1200

18' wheels - 1500

new t04 turbo - 900

new manifold - 500

new intake plenum - 600

bosche fuel pump - 550

malpassi rising rate reg - 150

microtech LTX16 - 1300

670x300 fmic - 600

fmic piping - 150

dump pipe/front pipe - 150

external wastegate - 300

neons - 200

future mods

rb30 - 100 (paid for)

forged pistons - 1100

supercharger - 350

piping - 100

n1 oil pump - 600

n1 water pump - 150

Not going to list them man but its somewhere around the $50K mark, good chance it’s a bit more really. The cars not that powerful but it’s had just about everything in it replaced, you could call it a 2004 GTSt :D The only think I have not replaced is the steering wheel, but that’s after market anyway :)

Guest RedLineGTR
Not going to list them man but its somewhere around the $50K mark, good chance it’s a bit more really. The cars not that powerful but it’s had just about everything in it replaced, you could call it a 2004 GTSt :) The only think I have not replaced is the steering wheel, but that’s after market anyway :)

geeez crazy shit :D

only got registered today and so far it's got the following:

$225 rear strut brace

$1000 brembo's

$30 door trim

$550 front pipes

=$1805 for 1 day rego lol, expensive toys but who here would have it any other way????? :D :wassup:

Let's see in less than a year of owning my R32 it owns me:

Pirelli tyres - $800

clutch cylinder + head gasket + turbo seals + major service - $1500

Walbro fuel pump - $170

Blitz boost gauge + exhaust temp gauge - $570

HKS turbo timer - $150

A'PEXi S-AFC II - $300

momo gear knob - $150

steering wheel - $100

tints - $220

A'PEXi Power Intake - $190

A'PEXi strut brace - $160

Blitz LM Intercooler kit - $840

Focal Utopia splits - $550

JL Audio sub - $175

misc. cleaning agents - $300

SAU seat covers - $50

Quicktrak stuff- $400

services - $300

insurance - $3300

rego + ctp - $800

to come:

gear to be installed - $650 :D

headunit - $400

interior re-upholster - $300

suspension - $1500

exhaust - $1200

rims - $1500

rotors - $800

$7500.00 including purchase of car quite pitiful really

$2500.00 car R31 skyline,aussie RB30 gx model

$1500.00 RB20 DET & box

$800.00 HYBRID fmic

$1200.00 microtech LTX-12

$1500.00 fmic piping,pod,tune,exhaust,bov,bits too finish conversion

200RWHP

In modifications, my car has cost me about $2,800 :(

...thats including the suspension, intercooler, turbo, injectors, clutch, new trim blah, blah,blah....

Now that i look at the figure on the screen it doesnt look so bad, but it feels as though i have spent a whole lot more on it :confused:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...