Jump to content
SAU Community

Recommended Posts

Now as I understand it, yes V-cam has been setup on non-Fcon cars (RP have done a couple Power FC examples) but i still believe they run the HKS electronics and controllers to build the V-cam map. (could be wrong on this) - what i asked Trent @ Chequered Tuning to do was different, i asked if the G4 could do ALL the controlling and we ditch all of the HKS electronics. I know the G4 can control variable timing setups, so why not Vcam? So in typical me fashion, i think of something a little different (ie Flex-Fuel) and hand Trent a box of parts and say "kthanxbye!" :D

This was a bit of a mission compared to the Flex-Fuel, and i thought maybe i had asked a bit much this time but Trent as usual, delivered the goods and we now have the Link G4 directly controlling the V-cam, and the plus side to this is that not only do you get a much higher resolution map than what you get with the HKS electronics, you now have all manner of additional parametres to tweak and compensation tables can be added for things like oil pressure etc. Thus the benefit of going directly off the G4 with all the updated capabilities it has.

Considering how much the ECU costs, and what i've asked for it do now... 'tis a good bit of kit! :D

I got some dyno sheets, but i asked for the wrong ones (my fault), so here's the phone pic Trent me after some tuning...

vcam_zpsc8bc4718.jpg

This is a pretty conservative tune too as i understand, quite a bit back in terms of timing at the top end and fueling is on the richer side too i believe. So i think there is still a little in the setup to go...

One thing to keep in mind is that this is the baby V-cam, range of swing is the smallest - as i'm 99% sure i have N1 pistons, i couldn't go any bigger. Down the track, if it comes time for a rebuild or freshen up, i'll make sure to get the pistons to allow for the Type B range of Vcam.

As we've been sorting out some MAP vs TPS issues, the graphs are a little lazier than what the car actually has been setup for previously, so you can shift most of that to the left a little more as well when it's back to where we want it :)

If Trent finds the thread, i'm sure he'll have some more to add but she really is nice to drive and as with all 'new' things, there were some hurdles along the way but the end result is worth it :) A million thanks again to Trent & Cat for once again entertaining my different ideas and coming through with the goods!

There are some possibilities opened by this setup that didn't exist before... that is locally developed V-cam (as a lot of people are on newer gen ECU's, i'm sure there are a lot of variable timing capable) but perhaps that's a project for a different day hahahah - the benefit of this setup is that if replicated you wouldn't have to take the head off (ie RB25 NVCS retro mods) making it much cheaper.

wonder how she'd go with setup replicated on exhaust side............................................... :D lol

Awsome man. Looks like it has really woken up the 2530's in the area which matters on the street. How much of a difference to drive is it?

It's great that the Link is doing it's thing! *mega thumbs up*

There are some possibilities opened by this setup that didn't exist before...

Thanks for the feedback on this Daniel, I am hoping this means the G4 is able to be programmed for the VQ25det cam actuation also. Do you have any information you can send on the adjustments/settings available? Link were no help when I asked.

Very nicely done guys.

Although I'm not sure why you thought the G4 might not be able to? It's just an RPM switchable output.

Even a microtech will do it if you ask them to put the output in the firmware.

Very nicely done guys.

It's just an RPM switchable output.

Even a microtech will do it if you ask them to put the output in the firmware.

No its not. and no it cant :P

No its not. and no it cant :P

Well I've never seen a Vcam setup so maybe they do it differently to everyone else.

Can definitely get VCT control put in a microtech though.

Obviously the Link does it better but it's gotta be quite a simple task right?

Well I've never seen a Vcam setup so maybe they do it differently to everyone else.

Can definitely get VCT control put in a microtech though.

Obviously the Link does it better but it's gotta be quite a simple task right?

its nothing like vct, vct is a fixed on off, VCAM is the same as scottys vq25 setup but only on the exhaust side (from memory the vq has fully variable intake and exhaust). its simple enough in theory on a factory built motor where rpm and advance / retard is predetermined but on an engine not designed around it things go bend and snap.... it is very easy to kiss valves so all the thresholds of retard and advance need to be carefully measured is not just a case of winding in 20 degrees like vct does. This travels alot further among other things.

The hks controller takes care of all the end points once you input the zero point... i had to work it out with a dial indicator as we have no zero point :P

Thanks for the feedback on this Daniel, I am hoping this means the G4 is able to be programmed for the VQ25det cam actuation also. Do you have any information you can send on the adjustments/settings available? Link were no help when I asked.

it will have no issues but the config is a real headache (everything i was told setup wise turned out to be incorrect), it took me 1-2 days to nut it out as i was terrified of doing an accidental valve job :P we are talking big angle adjustments so things definitely hit.

its nothing like vct, vct is a fixed on off, VCAM is the same as scottys vq25 setup but only on the exhaust side (from memory the vq has fully variable intake and exhaust). its simple enough in theory on a factory built motor where rpm and advance / retard is predetermined but on an engine not designed around it things go bend and snap.... it is very easy to kiss valves so all the thresholds of retard and advance need to be carefully measured is not just a case of winding in 20 degrees like vct does. This travels alot further among other things.

The hks controller takes care of all the end points once you input the zero point... i had to work it out with a dial indicator as we have no zero point :P

Ahh yep, fully variable then. Yeah that's not so easy. Only systems like Motec, Link, Wolf would be able to do that sort of stuff.

We haven't played around with the standard VCT setups that much but would be interesting to see if the solenoid can be PWM'd to give a variable result like that.

How do HKS activate their setup?

it will have no issues but the config is a real headache (everything i was told setup wise turned out to be incorrect), it took me 1-2 days to nut it out as i was terrified of doing an accidental valve job :P we are talking big angle adjustments so things definitely hit.

Without Link's support I put the G4 Extreme in the too hard basket. I would have thought there were enough of these Stagea's in NZ now for them to make a plugin, but I guess the numbers are too small for them to bother. Shame, it would be perfect for these engines with the throttle control module...

I tried out the Vmanage, it isn't programmable and is only setup for the VQ35 hydraulic actuators. On the VQ25 the electromagnetic actuators hit their end stops with a bang at any more than 5 degrees input, it would have been either 40 or 50 degrees advance on the intake. The PWM frequency was completely different as I found out. :blink:

For some reference, I lost over 40kw in the midrange and all my response without the cam advance operating.

it will have no issues but the config is a real headache (everything i was told setup wise turned out to be incorrect), it took me 1-2 days to nut it out as i was terrified of doing an accidental valve job :P we are talking big angle adjustments so things definitely hit.

Seems weird that they wouldn't mechanically limit the maximum camshaft phase angle on STD engines. I hate the though of software controlling the maximum phase angle. I've had to do the same thing on some of the 3v ford v8's when they upgrade the camshafts - never had any issues but still make you nervous.

I'm assuming 50% drive is your neutral position? If so make sure you limit your max and min pwm drive to around +/- 10% from your neutral drive. Not sure if you can setup cam error tolerances with the link but you would probably want that too so that if you error is too great for too long it will go back to neutral drive. Be careful with running too much proportional gain and make sure you inhibit control below say 1500rpm.

Ok,

Sorry i'm a bit lost....... so these cams are not mechanically stopped from over advancing/retarding and could smash engines by being 0 or 100 % duty in the wrong time?

We setup VCT on engines that don't have VCT........ Has any one actually ever damaged a valve/piston from PWM VCT, or even switched VCT for that matter? has any one ever actually measured Crank degrees vs valve lift vs piston clearance?

Im very interested. I have done plenty of PWM with all the cams (mostly 4) on engines. I have never hit a valve as a direct result of the VCT being setup incorrectly in the software, only being setup incorrectly mechanically.

If you knew some of the lift/durations we run i think the word impossible would be thrown around a bit.

Ok,

Sorry i'm a bit lost....... so these cams are not mechanically stopped from over advancing/retarding and could smash engines by being 0 or 100 % duty in the wrong time?

We setup VCT on engines that don't have VCT........ Has any one actually ever damaged a valve/piston from PWM VCT, or even switched VCT for that matter? has any one ever actually measured Crank degrees vs valve lift vs piston clearance?

Im very interested. I have done plenty of PWM with all the cams (mostly 4) on engines. I have never hit a valve as a direct result of the VCT being setup incorrectly in the software, only being setup incorrectly mechanically.

If you knew some of the lift/durations we run i think the word impossible would be thrown around a bit.

Most OEM stuff is mechanically limited, by either having enough piston to valve clearance or mechanically limiting the advance/retard (I know this for sure on all EJ sereis motors, 4G63, 4B11, BA-FG falcons, have played around with some toyota and nissan VCT but never tested/Checked for piston to valve clearance).

Also you dont need to drive at 100% to make valves's hit pistons, if there is no mecahincal limit, all you need to do is drive the spool solenoid(if that is what is used) at say 60% for too long to cause it to go to full advance/retard depending upon the engine type......

I'm a little nervous here - I would have more confidence in an OEM ECM that has the cam phasing control loop optimized from factory to limit the max phasing, but I'm not quiet sure I would trust and aftermarket ECM..... There maybe more about the system I dont know - care to elaborate trent? I've also want to get my hands on the V-Cam setup.

Edited by rob82

Nice result! Makes a really solid difference :)

You are the guy that Chequered did the Flex-Fuel tuning on as well, eh? Would be interesting to see how the setup goes on ethanol + VCAM!

Pretty cool having the combination of someone keen to try interesting combinations, and a tuner with the inclination and ability to carry it through.

Loving this Dan - very nice. You are doing everything I want to do. Exactly the direction I would like to head with my 32 in the next year or so.

go to full advance/retard

NEVER go full retard!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
    • Oh and some up-and-comings; New rear drivers wheel bearing. I'll do that this weekend while the diff is out. The car is already up and the d/c axles and missing exhaust will help with space. This is the last bearing for me to do and I've been dragging my feet on it. I also have some new EBC blue stuff pads for the car and some new brake fluid. I haven't ever flushed the fluid in this car and looking forward to it. I have 600 degree fluid to put in. Not exactly "race fluid" but better than the typical stuff I have been using.
    • A proper clutch/plate type mechanical diff with quite a lot of pre-load and high locking % is better for drifting. Much more consistent in its behaviour. A helical can be annoyingly vague and inconsistent in how it responds under the sorts of abuse found in drifting.
    • Some updates here. I pulled the entire interior out, minus some trim to respray the seats with Colourlock dye. It turned out really nice though I accidentally let the dog in the car after and she scratched up the front seat.  This is what it looked like before, the colour was just washing out everywhere but thankfully the leather was in good nic. Then after the respray   And after the bloody dog jumped in The headliner is out waiting to be retrimmed, but it will stay out now until Nov - see why below. I replaced the stereo/headunit with a period-styled Android headunit. I have no after pics, but I'll get some. This is because of the missing pixels. I tried to fix this twice with replacement ribbon cables but couldn't. Also the bluetooth interface I'd bought for this was crap. Then there's the rusty roof. Pics and info in this other thread. I have decided to get this repaired professionally, but I'll update that thread. This is why the headliner will stay out for now. I'll be getting the roof and bonnet resprayed at the same time the rust is fixed. I also had an interesting issue with my drivers door lock.  For a small period I was having issues getting any 12v power to the car - I mean *any*. It would have no dash lights, nothing. It happened while I was at the shops and I couldn't get in the car. So, we had 2 problems. The most pressing here is that I was locked out. I have only a single physical key hole on the car, the drivers door and no amount of turning would unlock the car. Surely it doesn't need power for this? The second issue is why am I losing all power periodically, The battery isn't dead, its almost like the battery isn't even there. Two issues that were surprisingly easy to fix. You fellow BMW over-engineering lovers will appreciate this. The lock in the door has 5 states; mechanical lock, electric lock, neutral, electric unlock, mechanical unlock achieved at -90 degrees, -45 degrees, 0 degrees, 45 degrees and 90 degrees. Although, the unlock is towards the front of the car, so opposite for LHD countries. Sticking the key in and turning 45 left or right is what is used 99% of the time. It activates the central locking etc. 90 degrees is for dead battery access and, obvs, only un/locks the one door. But because the mechanical lock is never used and is 27 years old, it seizes up. I was totally unable to turn the key far enough to get to the mechanical unlock (At the time of locking myself out, I didn't even know this was a thing). I eventually did it with some vicegrips and teflon spray.  I made a quick vid for other E39 peeps.   The battery issue is totally new to me also - It wasn't making sufficient contact between the post and the terminal. The terminal was bolted on tight, but the car wouldn't have power. After checking the battery with my multimeter I accidentally contacted the terminal and the battery post and the car got power. The battery was only a few years old and in good condition. I cleaned the post and the terminal with a wire brush, bolted it back on tight and never had the issue again. I'm still surprised that despite having solid contact it didn't work. Also, the car was getting Warragamba sized pools of water in the back when it rained. My initial concern was another rust problem. But when I went out on Weds while it was raining and while I had no headliner in I could see a steady stream of water coming through the roof mounted aerial. As this aerial is for the (now removed) car phone I pulled it out and whacked a blanking grommet in the hole. It seems fine now. I'm thinking I might get the hole permanently filled when the rust is fixed. Moving forward and things in progress; The tailgate needs some attention. I have taken all the trim off to clean it all and address some small rust spots. I have partially done all of this but I'll finish it up hopefully this weekend. As all the trim are now entirely devoid of trim clips I have bought a heap of strong velcro and I'm hoping it does a good enough job as any of this trim in good condition is super expensive and usually in Europe as we dont have many of the wagons here. Suspension and brakes!!! This is exciting. In the front; New control arms New sway bar links New lower Eibach springs (the only modification I'm planning on this car) M Sport shocks (these came with the car and will replace the longer shocks in the car) New top mounts Used 540i calipers (stock brakes suck!) New 540i disks and pads (22x296 mm for 528 and 30x334 mm for 540i) New front wheel bearings (thank all that is holy for bolt on bearings!) Annnnd in the back; New control arms New sway bar links Adjustable air suspension arms (fool the car into what the current height is so the self levelling suspension can match the new front ride height) New ball joints I'll also be doing a brake fluid flush while I'm in there. I'm planning on switching the car over to the 16's that came with it so I can clean up and respray the M Sport 17's. They've lost a lot of colour over the years and have some gutter rash. None of this will start until the E90 is back.
    • You mean you will regret it for drifting duties? I don't quite follow.
×
×
  • Create New...