Jump to content
SAU Community

Recommended Posts

good to hear you got it sorted easily and most importantly cheaply

Many thanks - definitely the place to go people - the owner has a Skyline - his and mine could be twins---!!! I ended up staying out there for almost an hour - we got chatting (as you do with another Skyline owner). He has this plastic clean stuff in a tube - got in from Just Jap he said. Anyway he cleaned my headlights and they came up a TREAT. All that yellow milky yuk that gets over them is goooonnnnee

;):)

  • 2 weeks later...

I had some work done by Canberra Motor Works. Cost nearly twice as much as originally quoted, twice as much as another quote, three times longer to do than they said (done lots of these mate), and they only charge $90 an hour for the 19 year old. Included strategic application of body scratches and the deliberate defacing of original underbonnet decals. Apparently I wanted that done for $90 an hour. Oh and a bad photocopy of an owner's manual for only $20.

Quality work at unrealistic prices. Can't recommend them more lowly.

Figured it's worth posting, the NRMA 24 Hour Battery guy showed up today nice and early. Wasn't the most talkative guy but he was very quick. Tested my original battery which was dead, and managed to take it out and put the new one in without removing my rear strut bar so i'm pretty happy about that. The replacement battery was $109 and comes with a 2 year warranty.

I had some work done by Canberra Motor Works. Cost nearly twice as much as originally quoted, twice as much as another quote, three times longer to do than they said (done lots of these mate), and they only charge $90 an hour for the 19 year old.  Included strategic application of body scratches and the deliberate defacing of original underbonnet decals. Apparently I wanted that done for $90 an hour. Oh and a bad photocopy of an owner's manual for only $20.

Quality work at unrealistic prices. Can't recommend them more lowly.

EEEEEEEWWWWWWWW - thats terrible

Jaysus - you should've written 'em a REAL nasty letter after that and put a very visible CC: on it to Fair Trading and some sort of Automotive Association (like NRMA) and the ACT Ombudsman as well... Don't get mad - get even!!! ;):rofl:

Just had my R34 serviced for the big run back to Cairns.  Had it serviced by Joe Fister at the Mobil Servo at Garran.  I have nothing but praise for the guy.  Only required a basic service this time round but he is a Skyline fanatic.  Many thanks to Jeremy for the recommendation.  Motul 4100 Turbo light in the engine, Redline in the gearbox and Motul 300 in the diff.  All good I say.

Cheers

Muz

Agreed!! :rofl:

I got brake pads, the discs machined, oil & filter change, gearbox oil change, new spark plugs...plus the usual check over of everything... they also fixed my mis-firing i was getting at high revs.

very nice guys (Joe and Charlie), very helpful..and Joe loves his skylines!! ;) I'll be going back for sure....and not just because Joe promised me a ride in the other wine red R33 they had there that has apparently had some serious $$ spent hehe :)

that otherwine red R33 is his friends jason's and it has had some $$$$ spent on it.....when i was down in canberra we were getting them worked on togerther and my only retriction was the $$$ so ultimately he won when it came to power but i won when it came to driving skills HAHAHAHAHA

Jeremy

Figured it's worth posting, the NRMA 24 Hour Battery guy showed up today nice and early. Wasn't the most talkative guy but he was very quick. Tested my original battery which was dead, and managed to take it out and put the new one in without removing my rear strut bar so i'm pretty happy about that. The replacement battery was $109 and comes with a 2 year warranty.

$109 is good, i take it that you went for the base model battery? i think they have the best one for like $149 or something.

i think i might have to get mine checked, alot of the time in the last few months the car seems to have no charge and barely starts!? the other wierd thing is that my parkers always stay on while the car is on. and my dashlights too, i think i must have cross-wired something when i installed my high mount brake light.

i don't think it was the base battery... i dunno... the guy knew his stuff and we haven't had a problem with it yet.

On another note i had my alarm completely installed today. My dad had taken it down at 8 in the morning on Friday, and by 4 they were still working on it, asked him to bring it back at 8 on saturday morning...apparently there was only an hours work left but it turned out to be about 3... anyways, got the car back and the alarm is fantastic. Not a problem yet.

Very quality installation and all-round nice guys to deal with. Can't see any scratches or marks on the car and the section of dash that had to be cut is neat and clean.

If you need any auto-electrical work done then definately see the guys at the Tuggers auto eletrician down near the Wollworths servo.

  • 2 weeks later...

Hey,

I'm looking at getting a FMIC for my R32 but can't seem to find any kits.

Anyone know who stocks them in ACT or Sydney?

Also anyone done this sort of work before?

Do you need to cut any metal, I had friends who have installed FMIC's themselves on 200SX and they needed to cut holes near the battery....ect

Also if anyone knows how much the kits might cost?

Don't know about ACT but Advan in sydney would probably have a couple of Jap brands in stock. Give em a call - could be looking at up to $2000 for a jap kit with all piping! People have recommended Nengun for good deals and quick delivery from Japan. I read that someone got a HKS type s kit for r32 gtr for less than $1500 through them.

  • 2 weeks later...

I think I need to get my gearbox rebuilt.

I just want it to change gear smoother, when I change gear into 2nd i feel all the cogs moving so I have to force it in not nice to cruise around, also going into 3rd I have to got to the middle of the H pattern box then into 3rd so I have to wait about 1/2 a second before, now I've driven other cars and they change alot smoother than mine.

I have changed the oil and replaced it with redline but still no good.

I wonder if anyone knows where I can get it rebuilt, I don't want to pay heaps either, but then gain who does :)

Any suggestions from people who have had this work done before would be appreciated.

Cheers Adam

Agreed!! :)  

I got brake pads, the discs machined, oil & filter change, gearbox oil change, new spark plugs...plus the usual check over of everything... they also fixed my mis-firing i was getting at high revs.

very nice guys (Joe and Charlie), very helpful..and Joe loves his skylines!! ;) I'll be going back for sure....and not just because Joe promised me a ride in the other wine red R33 they had there that has apparently had some serious $$ spent hehe ;)

Finally got to ride shotgun in their wine red line!

Still can't get the grin off my face - :wassup: !

That is one powerful car.

Should prolly post back that my dad saw Ed at intergra autmotive and he had a look over the car. He sure knows his stuff! My car had an afermarket speedo (NISMO) put on at about 40,000 kilometres which made the reading start at zero again. Anyways, it's showing 28,000. Took the car to Ed, he had one look over it not knowing the deal with the odometre and told us that it definately hadn't done 28,000 but closer to 70,000 which was spot on.

A few things were dont to my car, to the tune of $1300... although i can't say i was surprised as the car had been sitting around for over a year unused not including the time it spent in Japan.

To cut it all short, haven't had a problem since and the car is running better for it, more responsive then it was before.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
  • Create New...