Jump to content
SAU Community

Recommended Posts

There is a bit of talk about what mph a car should run at the drags with a given power output, thought be good to get sum results and discussion on this.

Be good to get sn idea of what mph a skyline should run with say

300rwkw

350rwkw

400rwkw

450rwkw

Etc.

So people post your mph results (1/4mile or 1/8mile, or both) and what power the engine made, and model of skyline.

Edited by sky30
Link to comment
https://www.sau.com.au/forums/topic/418443-mph-vs-power/
Share on other sites

400awkw 11.3 @ 125mph

500awkw 11.2 @ 130mph

Full weight R34 GTR:- spent lots of dough to get 100 extra KW and only dropped .1 of a sec and picked up 5mph in the deep. ( both with 1.7 Sixty's )

Should have let someone who could drive have a crack. Seen an 11.007 @ 127 same car 350awkw.

Link to comment
https://www.sau.com.au/forums/topic/418443-mph-vs-power/#findComment-6721086
Share on other sites

what time was that?

did you get half track MPH?

11.3 I think it was. It wasn't on the best surface. Half track NFI. I'll head back to the drags after my tune is complete and give it another go. Car has gone 11.1 previously.

Link to comment
https://www.sau.com.au/forums/topic/418443-mph-vs-power/#findComment-6721285
Share on other sites

400awkw 11.3 @ 125mph

500awkw 11.2 @ 130mph

Full weight R34 GTR:- spent lots of dough to get 100 extra KW and only dropped .1 of a sec and picked up 5mph in the deep. ( both with 1.7 Sixty's )

Should have let someone who could drive have a crack. Seen an 11.007 @ 127 same car 350awkw.

125mph and 400rwkw don't really match, power is certainly down there. Even @ 500rwkw you should be sitting 134mph EASY.

R33 GTR 340rwkw

11.5 @ 123mph

Full weight (full tank & spare in the boot) with a larger sump (9.5ltrs)/brakes/oil cooler etc + 85kg driver.

I wish I'd put it on the scales to see how much over factory with all the extras.

HR31 GTS-R 220rwkw @ 1480kg

11.9 @ 110mph

Link to comment
https://www.sau.com.au/forums/topic/418443-mph-vs-power/#findComment-6721318
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...