Jump to content
SAU Community

Recommended Posts

It's more to do with the fact that the shocker mount were never designed to take the weight of the vehicle.

Now that the coil overs are mounted to this spot I have just added extra bracing to transfer the load back to the original spring pocket/body rails.

Got some suspension and other bolts zinc plated and picked up some inner and outer door handles. 

 

Sent Bonneville Consulting and email tuesday but haven't heard anything back yet.

 

IMGP3389_resize_zpsm44efmai.jpg

Started fitting the back seat, needed to modify the seat base to fit over the skyline tunnel.

I used the seat base out of a UC hatch that I brought for spare parts but it may turn into a future project and wont need a 

back seat. ( S14 front suspension, R32 rear suspension, drift ute, maybe)

The wire frame was a bit bent so it had to be straightened and reshaped over the tunnel.

IMGP3394_resize_zpsco1onvrk.jpg

IMGP3395_resize_zpssjpbgsed.jpg

Rigged up a hot wire to cut the foam.

IMGP3392_resize_zpsr43fk3zv.jpg

All fitted up, I will probably only register the hatch as a 4 seater as there isn't mush foam left in the middle seat.

IMGP3391_resize_zpsszolawfp.jpg

 

 

  • Like 1
  • 4 weeks later...

Gave the drive shafts a clean up and some paint.

 

IMGP3397_resize_zps8ussojir.jpg

 

Removed some of the lip on the fire wall and fully seam welded it.

 

IMGP3396_resize_zpss2wyooym.jpg

 

Added some more strengthening to the front suspension towers to make sure the load is transferred back to the rail where the original subframe mounted. 

 

IMGP3398_resize_zps0za23c1h.jpg

 

  • Like 2
  • 4 weeks later...

Have contacted a few engineers to see if they were interested in taking on the project. I've chosen one, now I have to reassemble the car

so he can see where it's at and where to move forward from here. Hopefully he will look at it in a few weeks.

 IMGP3419_resize_zps4xz2je4m.jpg

 

IMGP3426_resize_zpsv8wubuia.jpg

 

IMGP3434_resize_zpsre3c0d5d.jpg

  • Like 6
  • 3 weeks later...

Had the engineer, Peter Turner http://www.techedaustralia.com.au/ have a look at the project.

He is happy with what has been done, he wants an extra brace between the rear suspension towers and I

have to have retractable seat belts for the outer back seats. The car will have to pass the IM240 emission test

and also have a torsional rigidity test. The plan now is to get the car ready for the torsional test then 

start the panel work.

Rear seat belts something like this.

IMGP3441_resize_zpsfopdubqe.jpg

 

  • Like 3
  • 2 weeks later...
  • 2 weeks later...

Decided to mount the seat belt reel besides the back seat so they don't stand out as much.

IMGP3454_resize_zps3ltzd5zb.jpg

Ground up a piece of flat bar to match the shape of the panel.

IMGP3451_resize_zpsz9lp2wxa.jpg

Will also weld this comp plate over the outside when the engineer gives me the ok.

IMGP3455_resize_zpsbgrgutk8.jpg

Also made up some panels for the back out of some aluminium that i'll cover with some vinyl.

IMGP3449_resize_zpstvagz2hw.jpg

 

  • Like 3
  • 3 weeks later...
  • 1 month later...
  • 2 weeks later...

Started fixing the rust in the tail light bucket.

ZDyXcFG.jpg

First had to get dogs ok on the tail light bucket from the spare parts car.

esyfN8J.jpg

HAZDvLz.jpg

Only going to replace the bottom half but had to do a small repair first.

ts16BTr.jpg

6B982Sk.jpg

Had to repair some rust in the corner. 

ATV1bbQ.jpg

ZHZryEO.jpg

Bottom replaced.

11LD6hU.jpg

  • Like 6

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...