Jump to content
SAU Community

August Monthly Meet - Wednesday 14Th August - Kebab Joint


Recommended Posts

Kebab joint. A nice place on a cold night.

This month we are having our meet at Kebab Joint - Im yet to find a better kebab, and I've been around.

When: 14th august 2013

Where: Kebab Joint

Corner Springvale Road and Princes Hwy Mulgrave

maps

Time: 7 PM onward

This is an Open event you do not need to be a member to attend this every-one is welcome.

We ask that attendees obey all Road rules.

we don't want people racing up and down the street or general Hooning.

remember you are representing the club

Here is the Menu's to get your mouth watering!

526139_10151199484089973_1434468779_n.jp

555528_10151199486234973_661097524_n.jpg

There is plenty of Parking too

See you all there!

  • Replies 148
  • Created
  • Last Reply

Top Posters In This Topic

que?

im in and im bring my f**king hsv. lets see how many of you have the balls to gob off in person hahahahahahahahaha!

i kid. will be good to put some names to faces.

Edited by Plattsy

aaron might have to see if scotty is heading up, might have to head to us and follow him up. f**ked if im going an hour south from hallam to sit in my house for ten mins before driving back north again!

This time, stay around for longer for a photo of your Toyota 86.

Haha!

Had movie to attend, friend. I will surely stick around for sexy photo time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...