Jump to content
SAU Community

Recommended Posts

Hey guys.

New here. Name is Jason (Go by Jase). Awesome forum i have been floating around reading and searching for a bit now. Very interesting stuff. Anyway i have just bought my first Boosted car its a series 2 R33 Rb25DET Manual. I have basic knowledge on N/A engines but not much when it comes to boosting.

To get to the point i have been seeing alot of benefits with going a RB30 bottom end with a 25 head for the extra torque. What i want to do is buy a RB30 bottom end and put the 25 head on there and put it in my skyline because its my daily so the extra torque would be good when not on boost.

Anyway i just have a few questions. Im new to the RB/import scene in general so please no hate or flaming me.

Is there difference between 30DET block and a N/A 30 block or is it just the internals?

What about between cars like any difference between R31 Rb30 or VL Rb30 or Old Pajero RB30 bottom ends??

Should i put my 25DET head on the 30 or a DE?

I want to keep the standard bottom end in the 30 and just put ACL race series mains and rod bearings or should i just use standard new bearings and new rings due to i am building the engine myself and just want to gain a little more experience before doing the whole forged everything incase it goes boom i wont be out of pocket to much.

Do i need to do anything to the crank when replacing the bearings like get it re surfaced? Or can i just leave it in there?

I want to use standard turbo for now at about 11 or 12psi so what would be a good CR for this without affecting off boost drivability? Goals are about 230/250rwkw

Can i use my standard 25Det ECU and loom untill i get the Haltech platinum 2000?

Im not going to put to many questions out there. While i keep looking any info would be muchly appreciated if anyone can give me any input. I havent found anyone doing something like this its all been worked motors with upgraded turbos,higher psi,lower CR for more boost etc etc.

Thanks heaps everyone. My R33 below. :D

60004_503534139740690_1101657975_n.jpg

Link to comment
https://www.sau.com.au/forums/topic/430474-first-boost-build/
Share on other sites

the 30et block and 30e block are same, just different pistons, when you say pajero (mitsubishi) im sure you mean patrol

no such thing as a 30det block, all30blocks are single overhead cam

i know your keen to build your own engine but you have had to ask some VERY basic questions

you may be better off leaving it to an experienced builder

Read your way through the RB30 upgrade thread at the top - quite a few non forged blocks like mine. If you are going to use the stock pistons you won't have much control over the CR but you will definitely get more torque. I don't think its worth doing it twice for the experience - build a forged bottom end and you can put all your stock head etc on top and upgrade the turbo etc at a later date. But do heaps more reading first and get to know how your present set up works before attempting to modify.

the 30et block and 30e block are same, just different pistons, when you say pajero (mitsubishi) im sure you mean patrol

no such thing as a 30det block, all30blocks are single overhead cam

i know your keen to build your own engine but you have had to ask some VERY basic questions

you may be better off leaving it to an experienced builder

Sorry yes i mean patrol. My mistake

Yes basic question for a basic build cause im not into a full build at the moment. I want to build my own for experience. I have done a couple commodore motors but thats it the only thing that gets me is boost.

Read your way through the RB30 upgrade thread at the top - quite a few non forged blocks like mine. If you are going to use the stock pistons you won't have much control over the CR but you will definitely get more torque. I don't think its worth doing it twice for the experience - build a forged bottom end and you can put all your stock head etc on top and upgrade the turbo etc at a later date. But do heaps more reading first and get to know how your present set up works before attempting to modify.

Oh yes that skipped my mind about using standard pistons with the CR. Yep im defiantly doing some more *studying* before attempting a build. I will be building a forged bottom end down the track but dont want to right now because i still dont know whether to build this car up or just save for a GTR.

Either way a set of rb30 forged pistons + correct CR rods are a good investment.

Assembling an engine is a pretty simple case of following the instructions; the only trick is to clean everything super thoroughly (especially oil feeds). The important stuff is all done by the machine shop in getting bearing, piston and head clearances correct.

Re a 250kw target, you will not get there with a standard turbo, it runs out of puff at no more than 200kw. Engine capacity doesn't matter; the turbo just can't flow enough air efficiently. I have about 250kw from my rb30 using a ebay t3 cheapy (although I have changed to a ball bearing core).

It should still run acceptably on the standard computer, but I would not push it hard without checking it on a dyno first, you may find it strays into strange parts of the map compared to standard

Either way a set of rb30 forged pistons + correct CR rods are a good investment.

Assembling an engine is a pretty simple case of following the instructions; the only trick is to clean everything super thoroughly (especially oil feeds). The important stuff is all done by the machine shop in getting bearing, piston and head clearances correct.

Re a 250kw target, you will not get there with a standard turbo, it runs out of puff at no more than 200kw. Engine capacity doesn't matter; the turbo just can't flow enough air efficiently. I have about 250kw from my rb30 using a ebay t3 cheapy (although I have changed to a ball bearing core).

It should still run acceptably on the standard computer, but I would not push it hard without checking it on a dyno first, you may find it strays into strange parts of the map compared to standard

Yeah im doing the assembly myself but will be sending it all off to a machinist to do the other stuff so i realised il be taking crank out anyway cause i will do those bearings aswell and get it balanced while its out. As i said the only thing that gets me is boost. Iv read that i should try get 8:5:1 or something close to that? Thought the standard RB30 rods were already strong enough??

I will defiantly be upgrading turbo as all the supporting systems down the line but for the moment i guess im just looking for a freshen up cause as i stated its my daily so will be driven alot. I was thinking today that forged pistons would be nice but what combo is best? As is turbo pistons and turbo head or N/A pistons with turbo head or N/A head with turbo pistons etc etc???

I know im making myself sound like i have no knowledge at all hahaha

Everything you are asking had been discussed before. There is a huge thread and a pdf file. It really can't get much easier, just search.

I have been reading that thread but its 357 pages long so its taking me a while haha :/ Thats if you are talking about the R33 RB30 conversion thread??

Go to eBay and search "wiseco rb", there is a package that has Wiseco piston and Manley rods

Anything from 8.5-9/1 comp ratio will work nicely

Yeah i searched that i can get CP forged pistons for like $1100 (roughly) or i can get pistons and rods for like $1200 $1300 so might as well get the rod and piston kit together as 1.

How would i get that CR? Like what headgasket,pistons, and head should i use?? What CR would i get with the turbo head and standard pistons?

I payed $1100 delivered for them thanks to the exchange rate at the time, get it with the 26 pistons though as they have a lower comp height and weighs less then the others, that's what I wished I had done but already had them by the time I figured it out

get a zero deck height the measure the combustion chamber volume and work out how thick the head gasket needs to be, I think I used a 1.2mm tomei gasket with a quick shave off the head and managed to get 9.5/1 C/R

I payed $1100 delivered for them thanks to the exchange rate at the time, get it with the 26 pistons though as they have a lower comp height and weighs less then the others, that's what I wished I had done but already had them by the time I figured it out

get a zero deck height the measure the combustion chamber volume and work out how thick the head gasket needs to be, I think I used a 1.2mm tomei gasket with a quick shave off the head and managed to get 9.5/1 C/R

Alrighty then. So what i take from this is to put 26 pistons in with 30 rods and crank?

Did you use the turbo head or N/A head for that CR and what pistons did you get turbo or N/A?

Yes exactly, which will mean you need to machine 2mm off the block to get 0 deck height which will lower head 2mm, and believe me in the 34 it would've made a difference for clearance over the motor

26 head, its in a R34 GTR, you need to CC the head to get its volume to work out comp ratio but I think the 25 has a bigger combustion camber, there is only two pistons available from wisco for RBs, 25 or 26 and the only difference is the compression height, both have 14cc dome tops

Hi Jase welcome to SAU nice 33 you've got there too :)

Just wondering what mods your car has currently has?

In my opinion building a 3L for 230-250kw is gunna cost decent money unless you're building the motor yourself of course. With a good tune, exhaust,intercooler & the usual supporting mods with say 3071 or 3076 or even a hypergear turbo your car will have good torque off boost and with the above mentioned turbos will achieve an easy 270kw on 98. P.S don't get a haltech ;)

Yes exactly, which will mean you need to machine 2mm off the block to get 0 deck height which will lower head 2mm, and believe me in the 34 it would've made a difference for clearance over the motor

26 head, its in a R34 GTR, you need to CC the head to get its volume to work out comp ratio but I think the 25 has a bigger combustion camber, there is only two pistons available from wisco for RBs, 25 or 26 and the only difference is the compression height, both have 14cc dome tops

So are you saying i should get the block machined 2mm AND the head machined whatever it needs to acheive the CR you have with say a 2mm headgasket maybe 1.5?? Or just the block?

Hi Jase welcome to SAU nice 33 you've got there too :)

Just wondering what mods your car has currently has?

In my opinion building a 3L for 230-250kw is gunna cost decent money unless you're building the motor yourself of course. With a good tune, exhaust,intercooler & the usual supporting mods with say 3071 or 3076 or even a hypergear turbo your car will have good torque off boost and with the above mentioned turbos will achieve an easy 270kw on 98. P.S don't get a haltech ;)

Thank you for the welcome. Indeed its nice i love it to bits.

Yes i am building the engine myself. :D As mentioned above i have the experience with rebuilding engines but thats on N/A so didnt have to worry so much about CR’s, Type of pistons etc cause it was basic rebuild but i want to take it up a notch with this build.

My skyline is dead stock. Not even a FMIC and only on 5psi :/ Why not get a haltech? Would the 25 computer be fine or should i get a 20 one and re tune it to run the 25/30?

hi Jason,

Check out spool imports they do a rebuild kit to suit rb2530 engines, I'm currently building a motor using one of these kits for my own car, as for a computer I'd recommend something like a Apexi Power FC, they are a good computer and I haven't heard anyway really have any problems with them.

XKLABA 2mm sounds like a lot to take off the block :\ are you sure it wasn't 2thou? 2mm is 80thou, I had my block decked 2 thou to simply clean the deck up and achieve a CR of 9:1 using the JE pistons and spool rods package with a 1.3mm cometic head gasket.

hi Jason,

Check out spool imports they do a rebuild kit to suit rb2530 engines, I'm currently building a motor using one of these kits for my own car, as for a computer I'd recommend something like a Apexi Power FC, they are a good computer and I haven't heard anyway really have any problems with them.

XKLABA 2mm sounds like a lot to take off the block :\ are you sure it wasn't 2thou? 2mm is 80thou, I had my block decked 2 thou to simply clean the deck up and achieve a CR of 9:1 using the JE pistons and spool rods package with a 1.3mm cometic head gasket.

Thanks i had a look and i might actually grab one of them kits. Id have to work out cost etc because its just a budget build while i build another fully forged 30 bottom end hence why i just wanted to re ring and new bearings to start with. Might still do it depending on CR i would get from the standard pistons from a N/A RB30 and a turbo 25 head.

Yeah 2mm 80thou, there is 3 comp height for RBs, you've got the 26 height then the 25 ones are 1.5mm 60thou higher and the 30 one are 2mm 80thou higher then the 26 ones, I've got the 25 ones and shaved .5mm 20 thou off the block to get zero deck height

This is just what I would do if I did it again, what you do is your choice, the reason I would do it way is clearance above motor on mine is that tight I had to put washers under the strut brace to clear the twin turbo pipe, plus the liter piston, from memory it's 60grams less then the 25 ones I've got now, would make a difference at 8000rpm

Yeah 2mm 80thou, there is 3 comp height for RBs, you've got the 26 height then the 25 ones are 1.5mm 60thou higher and the 30 one are 2mm 80thou higher then the 26 ones, I've got the 25 ones and shaved .5mm 20 thou off the block to get zero deck height

This is just what I would do if I did it again, what you do is your choice, the reason I would do it way is clearance above motor on mine is that tight I had to put washers under the strut brace to clear the twin turbo pipe, plus the liter piston, from memory it's 60grams less then the 25 ones I've got now, would make a difference at 8000rpm

Ok so what if i use 30 or 25 pistons? Would i need to get the block shaved by 2mm or just 1.5mm for the 25 pistons? Or just a resurface like the head?

I know of a few people having issues with haltech computers I could also show you a video which may change your mind about them lol. Mate id suggest spending your money on ya bolt on bits 1st cos if its 100% stock you will be VERY surprised how quickly it livens up when you get it breathing. :) If this is your 1st turbo car take my advice and do your bolt on power mods and see if you still think you need more torque ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...