Jump to content
SAU Community

Manifold Shortening For Bigger Turbo ?

CALEBSNZ

By CALEBSNZ,
in Engines & Forced Induction

 Share

Recommended Posts

CALEBSNZ Newbie

CALEBSNZ

Posted
Posted

So i got a new rb20det and its running standard 20det sidemount turbo , i want to put my t3t4 back on but its ennificient on a 20 kicking in around 4000-7000k i heard if manifold is shortened it will kick in quicker and be more effecient , is this true and is it worth it ?

CALEBSNZ Newbie

CALEBSNZ

Posted
  • Author
Posted

idk i was just told this by a mate and i wasnt really paying to much attention but i would assume turbo manifold , i just want more boost out of it and i already have the turbo so it would be good if i could run that but have it kick in lower revs

CALEBSNZ Newbie

CALEBSNZ

Posted
  • Author
Posted

yea stock manifold sidemount , thats what i was thinking but he said hes done it before and its a piece of piss so idk haha but it doesnt sound like something you would do i guess i would have to look into it more but i agree hacking into manifold doesnt sound logical haha

Ben C34 Grand Master

Ben C34

Posted
Posted

you can disconnect the actuator

Yep, easiest and cheapest way to unlock max boost, pull off wastegate line. (seeing as you got fairly confused about the manifold thing, that is a joke)

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

Tell whatever hybrid turbo you have. Buy a NEO6 turbo, it bolts straight on. Put the RB20 actuator on that and enjoy 10psi. It kicks in around 3,000rpm (probably a bit earlier if you had a full exhaust). Good for some fast driving, better fuel economy while putting around. Win win.

Dan_J Veteran

Dan_J

Posted
Posted

this applies to manifold pipe diameter, bigger pipe = more lag but some top end power, where as smaller pipe is more response but top end power is reduced

so stock manifold is more responsive due to smaller diameter pipe

you might have a boost leak or if not your running a r33 turbo/actuator for that 6psi

r32gtrs Rookie

r32gtrs

Posted
Posted

sounds like its normal for an ebay t3/t4 turbo (whatever that is who really knows) to spool extremely late on a 20. you cannot shorten the maniifold someones just talking crap to you. better off selling it and putting on an rb25 standard turbo. car will be like new car to drive, will be so much quicker and more enjoyable.

eightsixboy Mentor

eightsixboy

Posted
Posted

Op6 rear housing is a little big for a 20, considering you can't run a lot of boost through them I wouldn't bother, better of selling one he has and buying a 2530 or similar, at least will have the potential to make decent power and have great spool.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...