Jump to content
SAU Community

Recommended Posts

dido....takes the gloss of owning a nice car... in Sydney i was just staring to get a good network of ppl to look after me and my car, now in Melb have to go through the whole learning curve again....my car needs little panel work, but i think ill just stick with rain/hail dances

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Yer black is a bastard to paint and get nice.

 

So how do you think it will finish up? Doing what you mentioned above does it generally come up ok?  

 

I've already told him I don't want those nasty swirl marks you see in the sun. I used to have a commodore that was sherbrook green. Only after I bought it I realised it had bad arsed swirl marks that made the paint look dull when the sun was directly on it. It didn't have that nice deep look.

You can polish a car so it looks mint in the shop, take it outside in the sun and it looks like crap (or vice a versa). Alot comes down to how time the guy is prepared to spend on it. Once its had the runs and orange peel dealt with, it will need a heavy machine cut to bring it back up, whether it then shows swirls or not depend on his follow up system, or more likely the apprentice/shop hand who will be doing the actual polishing.

Swirls also vary by what pad they use, wool is be far the quickest but swirls pretty bad, foam pads are less prone to that, but have their own problems (like heat and grabbing), be interesting to see what they actually do with it, you should make a point of being there and watching, tends to improve the end result...

Merli & NRB,

Copyright practices generally use Postage Stamp dates as evidence in court. This is the only legal method I know of, that can confirm a specific date. That said, Joel could take digital or standard photos and slip them into 2 envleopes, send them to himself & store them for evidence if the repairer disputes his claims.. If the matter goes to court, then you prsent the "unopened" evelopes in court.

Merli & NRB,

Copyright practices generally use Postage Stamp dates as evidence in court. This is the only legal method I know of, that can confirm a specific date. That said, Joel could take digital or standard photos and slip them into 2 envleopes, send them to himself & store them for evidence if the repairer disputes his claims.. If the matter goes to court, then you prsent the "unopened" evelopes in court.

Interesting!!!

Well there you go Joel, get to it! :)

this doesnt surprise me ... most auto workshops of any kind use unskilled people to do a lot of the work ..ive had problems with almost every aspect of my car when taking it in... few examples...

-nuts comming off my dump pipe the next day

-compliance people leaving tools under my bonnet that fall out when i drive away

-wheel alignment guys not making my steering wheel straight

-electrical installers ****ing up installs and breaking the device

fun fun

I find it helps if you tell them straight up you are one picky motherf***er who is sick of getting screwed around and the work 'will look perfect, right?' and 'what will you do if the job is not perfect?'

Once you've made clear you are anally retentive, tell them your only behaving like this because of -insert random story of guys in similar industry screwing you around- or -because your mate got screwed- etc.

I find the job is usually done properly then.

  • 9 months later...
Merli, I wouldn't use digital media - I'd be taking the photos on 35mm and having them processed immdiately with a "summary" print showing all shots on the roll. This will have a date stamped on it, and you'll have an hard copy receipt too. Then it's difficult for them to say the scratches were made "in the last month". If you're really concerned, you can take digital shots, print several pictures onto a page, fold up the page and seal with scotch tape, and mail it to yourself. That way there's a franking stamp that's dated by Australia Post.

good idea, but they don't seem to stamp the mail anymore, obviously it is a little too hard!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I don't think the shuffle can damage the turbos. It only happens at low shaft speeds and loads. It's just annoying (to some people - others are tickled by the effect) and it quite possibly reduces spool performance a little bit.
    • Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
×
×
  • Create New...