Jump to content
SAU Community

Recommended Posts

The caltex on main north road in Salisbury is overcharging for e85. It should be around 20 to 25c below 91 unleaded, the last time I checked it was only 5c below. It's a pity as it's on my way to work. Is this the same for all caltex servos?

Reduced range is the only drawback, and jerries can fix that.

United have a great app for finding e85 servos nearby, although it can be slow to be updated.

Scotty you are the E85 man so rather than doing a search can you answer this quickly.

Does the decreased cost of E85 negate the reduced range?

I'm not 100% on the cost of E85 and from what I have read it's about 30% more fuel?

...

Does the decreased cost of E85 negate the reduced range?

...

Have a read of this over at LS1: E85: A Long Term Evaluation.

Based on his data, over about two years, the cost per km of running E85 was pretty much identical to running PULP.

However that was posted in October last year so prices (and how they compare) will have changed again since.

Ive read on here multiple times people saying e85 is cheaper, but you use more lf it so it ends up more expensive. But e85 seems to be about 25-30% cheaper than 98. If you use 25- 30% more fuel, wouldnt you assume itd end up equal? (obviously depending on how you drive.)

*im no mathematician :D

if you drive "sensible" it equals about the same, put your foot in and can almost see the petrol needle drop. on average day to day driving I lost 100kms per tank switching to e85, but pay about $20 less per tank. also made 40kws from the change.

WOW! That answer couldn't be further from truth! E85 will be 1 of the best things you do to your car :) 100 is just 98 with 10% ethanol (I think) will be nowhere near the same power gains or the same driveability 70% or 85% ethanol will offer. If ya not too accelerator happy increased fuel consumption will be minimal with a good tune.. But its hard not using it with the new found powerz lol :)

Dont bother with E85. Too much hassel for the gain. Try united 100. Almost the same power gain without the issues and costly setup of E85.

Just curious, what gains in performance are there from a lightly modified standard turbo car? I have a friend with the following mods who wants e85 but I think the money is better spent elsewhere... Anyway:

Eg rb25 with standard turbo, 12psi, standard motor, pod, fmic, nistune, 3" exh etc?

Making around 190-200rwkw, could he expect the same increases in power as someone with 300rwkw going from 98 to e85?

Been having a read of this thread - is there enough scope in stock RB25 NEO injectors to run e85 with the stock turbo?

Been having a read of this thread - is there enough scope in stock RB25 NEO injectors to run e85 with the stock turbo?

Doubt it... they are pretty small (370cc i think)...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...