Jump to content
SAU Community

Recommended Posts

Ive just launched my std turbo on my M35.

What are the current upgrades , given that i'm not planning on going major on the mods. I'd like more boost, but not a laggy pig either!

Do i just get a high flowed std turbo, like http://www.digi-hardware.com/m35highflow.htm , or a new unit ? Any recommendations ?

Link to comment
https://www.sau.com.au/forums/topic/442392-m35-turbo-upgrade/
Share on other sites

If you aren't planning on tuning the ecu via the Emanage ultimate or Fcon at some point, stick with as close to stock sized as possible. The G1 profile for $880 is a good deal, or a Sierra stage 1 some other builders use. You will notice lag either way, as the wheel is steel, not ceramic, but it shouldn't be to bad if you keep them close to stock sized.

Where are you located Mark? The part you should be more worried about is who is doing the swap...

What was the specs on the presicion turbo Dale ?.

Not sure on the emanage/fcon upgrade yet Scotty. I do all the work on my cars. (mechanic +22 yrs) this one wil be a challange, but i'm sure i'll manange with it. ( & swear a bit..)

Looks like i might have to fab up a new intake whilst i'm there. Bit of work to do & Loads of room to work on ! (lol).

There seems to be a few oil feed mods to do as well. What's involved with that ?

Thanks for your help gents !

I'm interested in this also. I have a spare stock M35 turbo to send off to Hypergear this week sometime and am trying to decide which option to go.

I have an emanage ultimate and Greddy Profec sitting next to the turbo that will be fitted at the same time so i'm leaning towards buying injectors and bigger fuel pump as they will peak out around the 200kw mark.

Stao from Hypergear recommends either the G2 highflow (rated up to 240kw on 98 pump) assuming you plan to add injectors, pump, emanage etc. He also put the SS2 profile on the table as well which will produce 270kw but i'm still looking for dyno results as lag is my concern also. I'm coming from a 240kw R33 so i'm looking for something similar (auto aside) from my M35.

At this stage the G2 is looking the goods for me.

  • Like 1

I also went with a high flow by Precision(same as Daleo) but went with an SS1. For me I was after nice low down responsive power. It is still slightly lagier then stock. But hardly noticable. But the power delivery and increased high end power is very noticable. I will shortly be installing 1000cc injectors a bigger fuel pump and an Adaptronic ECU along with a couple more bits and pieces, At which time i will upload results for everyone to see. My goal is to have very minimal lag.

Edited by Brick
  • Like 1

i got the hypergear SS2 with billet front wheel, and boy was it laggy driving it home from the workshop.

As scotty said if not tuning stick to as close to stock as possible.

And if tuning look into getting the wastegate bored out bigger and getting scottys waste gate actuator.

  • 1 month later...

Gday All,

Ive just been reading through this thread for my mate Lenny whos bought an M35. Hes keen to do a few performance mods but its hard to find info on these cars.

So far he has:

-made a less restrictive intake

-made a replacement stainless turbo intake elbow (less bendy and restrictive than stock)

-chucked on a hks frontmount (came off an evo, and fitted right on!).

Next up old mate will be building a 3 inch stainless exhaust, he would like to increase the boost or upgrade turbo if possible.

So I guess we will need to look at turbos available and also an ecu to support it, Ive read the threads whats the general consensus for an ecu upgrade?

I run a GT2871 on my RB20det cefiro but reckon that would be too small for the Stagea, Im guessing something about a GT3071 as its a 2.5L, does this sound about right?

Next question, is anybody running this and how much hassle was it?

thanks for any help,

Agent A31

Edited by AgentA31

See the preceding posts for ideas on turbos. The problem with ecus is the auto so you have really to piggyback something on to the stock ecu.

The Greddy E-manage is relatively cheap, anyone should be able to tune it and you may be able to find an adapter loom for it.

The HKS F-Con is a better unit but it is more expensive and few tuners have the software to tune it - looms are available if hard to find.

Then you can put anything else on you like - Link, Adaptronic? (ref the previous post) etc but that is a more expensive option and will probably have to be hand grafted into the loom.

I run a GT2871 on my RB20det cefiro but reckon that would be too small for the Stagea, Im guessing something about a GT3071 as its a 2.5L, does this sound about right?

Next question, is anybody running this and how much hassle was it?

How much coin does he have to blow? Not many of us running aftermarket turbo's, most are happy with a highflow for less headaches. Have you even seen how hard it is to get to?

  • 1 year later...
  • 3 months later...

So the time has come for an upgrade, would like to get roughly 290-300kw atw on 98pump with as decent spool/response time as i can get (yes i know pushing shit up hill lol) I believe i have all the supporting mods ready to go atm apart from injectors and obvious fabrication to fit the turbo in. I have included the mamba turbos because of price im open to other options.The EFR turbos are a bit more expensive but seem to be the goods. Im leaning towards the GTX3071R with a .82 or .63 A/R but would also like to see what the EFR7163 would be like! from the looks of things the GTX would hit full boost round 4000rpm with the .82 at a guess? the EFR with the lighter wheel maybe a few 100 rpm sooner? And space would be a limiting factor of course. the EFR Is of similar size to the GTX in circumference just a bit longer so that could be an issue. Any input or thoughts/suggestions would be appreciated!

EFR7064
70mm compressor (exducer)
52.2mm compressor (inducer)
64mm turbine
300-550hp
.85 A/R
ewg or iwg
EFR7163
71mm compressor (exducer)
57mm compressor (inducer)
63mm turbine
300-550hp
ewg or iwg
.85 A/R
ewg or iwg
GTX3071R
71.4mm compressor (exducer)
54.1mm compressor (inducer)
60mm turbine
340-560hp
.82 0r .63 A/R
ewg or iwg
GTX3076R
76.6mm Compressor (exducer)
58mm compressor (inducer)
60mm turbine
360-640hp
.82 0r .63 A/R
ewg or iwg
Mamba GTX3071R
71mm compressor (exducer)
53.1mm compressor (inducer)
60mm turbine
380-480hp
.82 0r .63 A/R
ewg or iwg
Mamba GTX3076R
76.6mm compressor (exducer)
58mm compressor (inducer)
60mm turbine
350-550hp
.82 0r .63 A/R
ewg or iwg
Edited by Reprieve

I would like to go external gate but I'm not opposed to going internal. The gtx looks like it will fit in close to stock location so if I went the gtx way I'd probably put it there, but other than that maybe remove air box lol?

Did you see my GTX install pics from 4-5 years ago? The GTX 3076 fits, but only just, and that was the external gate housing. Think 'Ship in a bottle' it wasn't an easy fabrication by any means.

Let me know if you can't find the thread as I should still have some pictures saved somewhere.

No, too damn laggy. :P I have tried a few 3071's, now i'm helping design a highflow to suit the stock converter and still flow close to 300kw on e85.

The Garrett would be fine with a high stall converter, (just ask Alex who bought my setup) but realistically a highflow will produce enough torque these days to toast your gearbox, without the need to rev it to 8k.

Unless you have full standalone control none of this is a good option, you running the Fcon?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Before I commit to it as I already have the wastegate off the car, would you change it to the 9psi spring instead of the 12, or whack it back on now and try your suggestion?
    • Sounds good Hmm suppose the main thing is, how much do you care about this car? The filler doesn't make for a very good water barrier lol. If there was a tiny little bit of rust forming now, that in 3 to 5 years time becomes obvious under the paint (starts to bubble up), would it bother you? 
    • I already have the ability to datalog the voltage... what I can't do is correlate it to what the gauge is showing when I'm looking at the data at a later date. Or something like this. Except getting the oil to 125C+ involves me going 200+kmh at the track so you can imagine this is a little tricky unless I do something like note what the voltage is when I am at the top of 5th gear so I have a point to reference on. Drove car today. O2 still reading richer because hopefully not a leak instead of massive restriction I've introduced. Car really doesn't sound like a LS. It's quite strange. Pulled a bit of fuel out up top. This does potentially explain why my spark plugs looked like the car was running pretty over-rich. If I was tuning it to a ~12.7 which in reality was far richer than that in the past. It will be handy to have the dyno WB to compare my WB to to compare notes that's for sure. At this point I'm happy to just sit in the passenger seat and tune the thing given I've got about 7 million hours on the platform lol.
    • Yeah I understand you have to pay for an updated map or subscription service or something. But I can't even find a current map for Australia. My map is dated 2017, but didn't this car version still sell in Australia until 2021?   Also, just as an aside, the navigation system warns you of traffic incidences ahead.....why would they include that on a map they knew is not receiving live information. I am forever going to be warned of an incident that probably existed for 30 minutes 8 years ago.
    • Car has been sold and I am now selling leftover parts. Prices are non-negotiable as I will sell to my mechanic if it won't sell here. Prices are firm except for the Random Parts listed at the very bottom. All parts are genuine except for the S-Tune front bumper. Volk Racing TE37SL 19×10.5″ +12 5×114.3 pressed graphite with P-Zero 275 30 19 tyres [USED] $4,500 Wheels are in perfect condition, have been sitting in my garage for the past 6 years. Tyres still have 90% tread, but since they're now old, I would not recommend you drive hard on them. K-Sport Super Sport External Reservoir Coilovers (made to order) [NEW] $2,500 Front spring rate 14kg, Rear spring rate 7.5kg Fork Type. You can read all about it here (https://www.k-sportracing.com/product_detail.php?Key=12). I was going to start tracking the GTR, but never got around to it. Paid $3500 (after USD conversion and taxes). HKS Kansai Service Tower Bar [NEW] $500 Never fitted in the original Japanese box. R34 GTR S-Tune Fibreglass Bumper [NEW] $500 No mesh - No Box - No damage - just dusty. Nitto RB26 Clear Timing Cover [NEW] $50 Couldn't fit RB2630 due to bonnet clearance. HKS Piping Kit Special Type (BNR34) & Apexi Power Intake Air Filter Kit & Password JDM Adapter [USED] $1,000 Missing some rubber hoses and supports, but you get what you see. Nismo NE-1 Weldina Turbo Back Exhaust & Custom 3.5"straight pipe [USED] $1,000 Needs some love, but perfect for those who want to go back to OEM+. Bayside Blue Aluminium Vspec Bonnet/Hood [USED] $700 Came off my GTR. Unfortunately, the tips have been slightly ground down. It will need some repairing. Bride Low Max Super Seat Rails [USED] $350 The price is for both sides. Will post pictures when I get a chance. Random Parts [USED] - negotiable Standard rb26 cams (intake and exhaust) $10 Stock amber front indicators $10 Standard GTR bumper lower side grills $10 Stock amber side indicators $10 Nismo Sports Resetting ECU $50 Water reservoir $10 Stock airbox mouth $10 Stock fuel rail $10 Stock coilovers from R34 GTR Vspec $100 PM me which items you are interested in. I do work 9-5, so I will be responding daily at best. Best time for pick up is after 5 and before 7 on weekdays, or i can work something out on weekends. I will only accept cash or PayID. Pick up only - located Epping NSW area.
×
×
  • Create New...