Jump to content
SAU Community

Ecu Plugin Development - Spare M35 2.5L Ecu Laying Around?

Jason Broadhurst
 Share

Recommended Posts

Jason Broadhurst Enthusiast

Jason Broadhurst

Posted
Posted

Hi guys!

I've got an itch to develop a plugin for my M35 2.5DET. It will use an Adaptronic 1280 ECU and a patch harness.

The ecu selection will be because I'm pretty familiar with Adaptronic's now days, and also because the 1280 has an unlimited scope for programming auxillary outputs. This can be used to drive the auto ecu, dash stuff and anything else required. The 1280 is fairly special in it's function block approach to aux programming.

Hardware wise, I will need a ECU (can be damaged I only need the plug/internal pins). Instead of plugging the stock ECU in, it will have the plug and then wiring off to 1280 instead.

I will develop a loom and tune while retaining all the standard functions of the stock ECU. While I am there I will create a detailed pinout of the ECU as well as a value table for each pin (voltages, signal etc)

Does anyone have a broken ECU laying around, or knowledge of where the plugs are available from? Can someone clarify if I can use any 3.5/2.5L ECU, they should have the pins just no internals if the pin is un-utilised for that model.

Cheers, Jase

Brick Mentor

Brick

Posted
Posted (edited)

I am about to have the 920 adaptronic installed. Are you sure you wont still need the standard ECU installed as well?

I know with my install i do.

Edited by Brick
Daleo Grand Master

Daleo

Posted
Posted

Good luck with this Jason; many hands make light work with this sort of thing.

There are a few guys who have spent a lot of time & money developing solutions for these cars; it would be great to see what some new blood can uncover.

Cheers, Dale.

Jason Broadhurst Enthusiast

Jason Broadhurst

Posted
  • Author
Posted

I don't want to butcher a working ecu if I don't have to.

If any ecu can go full stand alone, it is the 1280. There is a lot to output I think.

I'll keep an eye out on ebay but was hoping for a easy find.

Commsman Veteran

Commsman

Posted
Posted

Good luck Jason - I hope something comes of this.

Does the 1280 talk M35 CAN bus? Could be a tall order to control dash/auto g'box etc without the factory ECU involved somewhere along the line.

stripey Collaborator

stripey

Posted
Posted (edited)

from reading a bit lately the canbus system uses coded electronic pulses to send to different addresses ( sensors gauges ect ect ) on the same pair of cables.

correct me if i'm wrong ( could very well be ) but I don't think anyone has cracked the code ( sequence and duration of pulses ) for the M35 canbus specifically the vq25det.

mind you I hope I am wrong and this proves to work out for you jason

Edited by stripey
scotty nm35 Grand Master

scotty nm35

Posted
Posted

I have a blown one here I will kindly donate to the cause, but unfortunately you are bound to have many issues with this idea. I would be leaving the factory ecu in place, like HKS did with the fcon. Even GTR's leave the factory ecu in place in many cases to keep the attessa etc happy.

The Canbus is simply too different from anything else, most readers won't even pick the ecu up, let alone the other 6 computers in the car.

The electronic throttle will stump you without going cable, it is just too dangerous to run without protection using the twin TPS signals through an opamp to kill power when there is a discrepancy.

The cams are self learning. They change angle constantly and a slight oil viscosity difference will cause a completely different phase angle for a single PWM input. The stock ecu actually learns as the oil warms up and adapts. Quite complicated, and for this reason Haltech didn't incorporate throttle and cams into their 350z plugin until the latest Platinum pro unit. The 3 older ones used the stock ecu and were piggybacked afaik.

Anyway, not trying to be a naysayer, just easier to leave the stock ecu in place and trick it into staying happy imo. I am more than willing to go through all this on the phone if you want to bounce some ideas off me.

  • Like 1
Jason Broadhurst Enthusiast

Jason Broadhurst

Posted
  • Author
Posted

Interesting. The can seems a little more tricky than expected then.

Closed loop cam control should be easy with the 1280.

Throttle is of concern but with some failsafe logic and hardware like Scott mentioned very possible.

Want to pm me a phone number Scott, I'll give you a call when you are free.

Jason Broadhurst Enthusiast

Jason Broadhurst

Posted
  • Author
Posted

If anyone has a engine loom with a good condition ECU plug, it would help also.

If I can't get a stand alone to work perfectly, a patch loom in parallel with the stock ECU is always an option.

I am happy to pay for these things guys!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...