Jump to content
SAU Community

Where To Buy Genuine R33 Coilpacks


Recommended Posts

Yeh im getting my work done by donny at forced they are really busy at the moment dont want to hassle the guy over coilpacks when the car isnt ready for everything else yet

Edited by skewy33
Link to comment
Share on other sites

Cheaper than crappy Yellowjackets too!

Genuine? Cheaper than yellow jackets?

http://www.skylinesaustralia.com/forums/topic/406879-coilpack-replacement-bang-for-buck-what-works-the-best/#entry6484679

http://www.skylinesaustralia.com/forums/topic/187108-jjr-coil-packs-vs-oem-vs-splitfire-vs-other/page-21#entry7236243

Have a search around here, someone did a comparison of fake Nissan coil packs vs. real ones.

FYI, even though my GT-R runs off the factory actuators (so ~12psi), the Yellow Jackets have been working fine for 2+ years, lots of km plus two track days. I run 1.1mm gapped spark plugs.

People had YJ coils fail, people had Splitfire ones fail as well. Plenty of info around here to make up your own mind.

Link to comment
Share on other sites

YellowJackets - as good as they sound, as good as their marketing say they are.. they're only good for a stock application.

Once you start ramming in boost they misfire all over the shop.. then you increase dwell (as you do) and they die on you.

In my experience, Splitfires have always been superior even with silly dwell settings.

Link to comment
Share on other sites

Exactly, you get what you pay for. But why risk buying ebay "Nissan" coils for $300 when you can get Yellow Jackets with local support/warranty, the seller being an active member on this forum? (that's my point)

Anyway...

http://nissan.epc-data.com/skyline/ecr33/3915-rb25det/engine/220/22433/

That's not even the correct argument. Why risk buying yellow jackets at all, despite the warm fuzzies of forum trader and all that stuff, when they have a higher number of failures than Splitfires and don't save you much money anyway? I'd rather pay the extra and suffer the tiny failure rate of Splitfires than save 30% and near 1 in 3 failure rate that I've seen with yellows.

  • Like 2
Link to comment
Share on other sites

From my experience, stock application it works fine. So if your car is stock, and you need new coils, would you buy fake OEM coils or yellow jackets (assuming you can't spend more than $500).

Under the artificial limitation that I cannot spend more than $500 I would clean up my existing coils and/or buy some 2nd hand originals until such time as I had the money to buy Splitfires or new genuine coils.

Face it. $500 is co close to the price for Splitfires or genuine that the gap is almost meaningless.

Let's put it another way.....would you buy a known non-genuine Z32 AFM for, let's say, $100, given the knowledge that they do work and have been used by a number of people, or would you rather pay $200 for a known genuine one? The other part of that question is that the known non-genuine ones, whilst they work, don't have the capacity that the proper ones do, and therefore can't be treated as if they actually were a proper Z32 (ie you can't use the Z32 curve in PFC or Nistune). I see the Yellowjackets thing in the same way. They work, but they don't work well enough and reliably enough to justify the relatively small saving in purchase cost.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
    • Thanks for all the replies! I also wanted to ask if wheels that were fitted on Ford Falcons would fit the 350GTs as well? In the area I'm at there aren't that many options for secondhand wheels and new ones here are way out of my budget. From what I've seen, most of the wheels that are available that were fitted on Ford Falcons have an offset of +33 to +36, with a centre bore of 70.5mm whereas the stock 350GT's ones are 66mm, can't seem to find any hubcentric rings that fit that difference though. 
    • 215/45/18 tyres are probably a little on the low side compared to the factory tyre, it should be closer to a 245/45/19, which will get you about an extra 11mm of height, and should make you speedo read a bit closer to reality. 245/45/19s will be a bit too far the other way and you risk a speeding ticket as your speedo might read slower than your actual speed.  245/40/19s would be correct if you are going to 19in rims, they will give you a similar total diameter to the 245/45/18 tyres.  
    • That's something I forgot to put in my list. The aggressive anti-squat in R32 is a f**king menace. I still need to decide if I'm going to drag the subframe out of my car and weld in the GKTech corrector kit. The main reason to dither is the need to switch to spherical joints in the lower arm to account for the twist induced in the rear pivot caused by lowering the front pivot. And yes...we do put better subframes in R32s, and I wish I'd gotten an S14 one instead of an A31 when I did the "take off and nuke it from orbit" HICAS delete all those years ago.
×
×
  • Create New...