Jump to content
SAU Community

Recommended Posts

Ok, pulling the dash out tomorrow to replace all the bulbs for LEDs now that they have arrived.

is there anything i nee to know, anything which is likely to break or clips in odd places?

for the main cluster:
im assuming its simply unscrew the surrounds and remove,
unscrew the dash and remove and unplug one main plug

then replace bulbs, i know their positive/negative and not to put it back together before testing... done that before

the ac i have done before on a gts so again im assuming the same.

tripple guage i dont know yet but cant be harder than a 34 gtt tripple?


ignore questions as search found it.

http://www.sau.com.au/forums/topic/115618-r32-headlight-switch-and-dash-globe-replacement/



...... Tonight's pointless post, brought to you by rebellion bay spiced rum.

Edited by GH05T
  • Like 1

Ok where is this ... vaccume hose? Supposed to go? Just pokin out randomly by my batter all of a sudden.

20150201_172754_zps5g7vibwr.jpg

Dissappears under the plenum With the other hose which goes to the stock boost solanoid.

20150201_172859_zps6kgzvizk.jpg

no free nipples...

heard that before


20150202_073330_zpsgxoysheg.jpg

my guess is something has been removed or made redundant with the new intercooler hoses?

it dosnt have any vacuum or pressure and im starting to think it goes nowhere and hasnt since i have owner her.
either that or its a re circulation system for emissions and does stuff all generally?

Looks like a good candidate.

No chance of tracing it to the source ?

I'll take a pic of mine today. Got exactly the same thing. (Not connected)

I was curious and asked ESP about it and I was told it went to the sump :unsure:

Hence my comment above

Edit: I have a Nismo plenum and it appeared after it was put on

Edited by Sinista32

tried in the shed, my not tiny asian hands traced it simply to, dissapearing under the plenum, following the other vac lines from the boost solanoid but havnt traced it further. made no difference when running or revving and as said has no pressure or vac. and i just cant find anything else open ended to connect to within reach.

asked the Pavlou guys who recently did the heater hoses and they saw it too, they weren't sure what it connected to (not really looking as they were doing other things) but came to the same conclusion that it was doing no good or bad and left it alone which means it hasnt been connected for probably a year at least.

Edited by GH05T

hmmm, well im just gonna ziptie it out of the way for now. dont want it finding the radiator fan or anything fun like that.
will do some more searching later.


also

20150201_173348_zpslzfrpg5e.jpg

yay stock steering wheel

shit thing is... which is very odd, i still have the HICAS light coming on at exactly 10km into a trip. do i need to reset something or is it another fault somewhere else?

Does It run to a nipple next to the intercooler pipe? Line for the bovs.

Breather for the front sump goes to an upside down u shape bracket bolted to the underside of the inlet manifold. Usually a thin vac hose.

Not 100% sure if thats the hose you mean.

Edited by k_d

just a thought about the hicas light. does it keep blowing a fuse? check the fusebox inside the car, top row 7th along. its a 10a one. maybe try cleaning up the earth? theres the hicas module under the factory boost solenoid. the earth for it is close by.

i had mine come on randomly recently (light on and hard steering) and i blew a couple fuses trying to figure out whats wrong. cleaned up the earth and contact point, new fuse. all good now.

k_d

there is another pipe taking that up
20150202_073330_zpsgxoysheg.jpg

will investigate the sump side when i get it in the air, cant see shit from under the bonnet.


on the hicas light, i will check the fuse, its annoying that it follows the exact 10km and fail symptom with the new steering wheel, is the stock boss not doing something maby?
my thoughts are going back to just pulling the bitch out and getting the martini locks.

in reading the hicas removal threads i do like the idea that you can plumb the unused system properly so that the hicas light still functions for low fluid or pump failing errors.

use the posted diagram to help you where find where it goes.

grab that rogue vacuum hose follow its path until you get to the end of it. it doesnt lead to the abyss you just havent figured it out yet.

how does the car behave? like a boost leak?unlimited boost?

has the factory boost solenoid been removed? do you have an aftermarket ebc? could be the line does not connect to anything?

stock boost controller is there and plumbed in, dosnt act like any boost leak and hits stock boost only.
i will get on it when i have a chance. probably when i get the plenum off to do the throttle linkages.

yeah i went, was an epic meet, i'm guessing 2-3000 cars.

32 ran well, had a chance to really rev it out and go for a decent drive which was nice.

On the run i pulled up at a set of lights next to a white 32gtr to which i strongly suggested he give me his grey dished panasports.... he declined :P

met him after and turns out he is Josh , owner of Forge Performance who i might go and see for a few things along the way which we discussed, nice bloke, not sure if i have seen him on here.

on that topic, we were discussing the car and some of its oddities/ rarities which include

no rear wiper

all the n1 bits (bonnet lip, sideskirts, rear spoiler (albeit missing) vents ect)

nismo 260 dash

we have been looking into its VIN which is still a bit perplexing, especially the last 3 digits which seem to be early 89 model only.
currently checking it out in the fast thread to see what it spits out, but it seems all the parts on the car are genuine and not just stuck on after which is nice to know.

will report back if it brings up anything of real interest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...