Jump to content
SAU Community

Recommended Posts

On 09/02/2022 at 5:57 PM, r32-25t said:

As I said it’s a really small thing but sometimes they make big differences 

100%

Should replace the cabin light lens and all, I ordered all new ones too. They're actually CLEAR! not that yellow colour I see in every Skyline.

On 10/2/2022 at 12:09 PM, Dose Pipe Sutututu said:

100%

Should replace the cabin light lens and all, I ordered all new ones too. They're actually CLEAR! not that yellow colour I see in every Skyline.

I have been very tempted to buy a set 

  • Like 1
On 10/21/2021 at 9:07 AM, r32-25t said:

AF757C2A-E43A-42A5-874E-32E0FBFD21E4.thumb.jpeg.427930175e0ce2f316d81df979ab0cf2.jpeg

ran the wiring harness back in the bay and going to retape the parts in the bay to make it look new, 

Stalking your stuff as youre doing a super nice rebuild.

I saw the part above, have you looked at doing the braided wire wrap that you can slip over the top of an already made loom?

Looks super neat, and available in a HEAP of sizes.

Would look way nicer than retaped, but wont look factory.

  • Like 1
On 11/2/2022 at 7:29 PM, MBS206 said:

Stalking your stuff as youre doing a super nice rebuild.

I saw the part above, have you looked at doing the braided wire wrap that you can slip over the top of an already made loom?

Looks super neat, and available in a HEAP of sizes.

Would look way nicer than retaped, but wont look factory.

Didn’t think of it for the old harness will look into that, already intend to use it when I make the new harness for the ecu/engine 

  • Like 1

The boots on the rack were stuffed and the rack ends and tie rod ends are 30yrs old so figured I’d send the whole rack away to be rebuilt 

C8D1FEB4-91EE-4280-AA92-811844FC9A3D.thumb.jpeg.e72c18b1f42d157f2fc87c26f1f184ae.jpeg

Lucky I did because it turned out the shaft needed rechroming so hopefully should have that back next week and can put it back together again

  • Like 2
On 12/2/22 at 9:27 AM, r32-25t said:

The boots on the rack were stuffed and the rack ends and tie rod ends are 30yrs old so figured I’d send the whole rack away to be rebuilt 

C8D1FEB4-91EE-4280-AA92-811844FC9A3D.thumb.jpeg.e72c18b1f42d157f2fc87c26f1f184ae.jpeg

Lucky I did because it turned out the shaft needed rechroming so hopefully should have that back next week and can put it back together again

Who reconditioned the rack for you? 

On 12/02/2022 at 5:07 PM, r32-25t said:

Active power steering in revsby are doing it, they definitely know their stuff 

Do they accept drive in and drive out jobs?

I cbf spannering these days.

On 20/2/2022 at 11:33 AM, Dose Pipe Sutututu said:

Do they accept drive in and drive out jobs?

I cbf spannering these days.

I don’t think they do. Didn’t appear to have any hoists just racking as far as I could see 

On 20/02/2022 at 11:42 AM, r32-25t said:

I don’t think they do. Didn’t appear to have any hoists just racking as far as I could see 

Damn, looks like I might have to work lol

  • Haha 1
  • 4 weeks later...

B7FC562D-4BBA-429D-B9DC-6799BC96E50F.thumb.jpeg.7bc974f2d48b988b558eab5693786490.jpeg

rack came back a few weeks ago but I couldn’t do anything with as I was still waiting on other parts 

F34485D0-D588-4759-B55D-703DC7F75314.thumb.jpeg.c43b6a888b2bd17da3852f87d5324f74.jpeg

and a few days ago they finally arrived. Brand new genuine boots, brand new genuine rack ends, a gktech tie rod end set and nismo rack mount rubbers 

ED2FA208-139F-44F7-86D7-13EC132B96CF.thumb.jpeg.9e249e19a83d090bbb5b30bfcae4d4e4.jpeg

put them all together and now the rack is ready to fit back in 

  • Like 2

Rack is back in as I needed to be able to move the car for another job I was doing around the house 

also just got a memory come up in my phone and it was a year today that billet block arrived and yet I still don’t have an engine 

  • Like 1
  • 2 weeks later...

Decided seeing as it was 30 years old and are common for dying now I’d replace the g sensor 

09EC83CD-E224-419F-BCF6-DFC1577D5801.thumb.jpeg.afe4927bf67a3e6e3f02cb6a5a6d5f8e.jpeg
Old g sensor showing no signs of heavy impact

9882D95C-8B63-4DF7-801C-9BEB77E1C19D.thumb.jpeg.acbfa396335ca28d712d627eef6a3326.jpeg

new one is a digital g sensor from midori 

3E6AFB02-07C6-4DB7-AEE8-91DAD837A295.thumb.jpeg.63b0e9eb0f2a306efd29f7243664045c.jpeg

and bolted into the car, fits strait onto the original bolt and wiring clips straight in 

  • Like 4
On 11/4/2022 at 9:42 AM, r32-25t said:

Decided seeing as it was 30 years old and are common for dying now I’d replace the g sensor 

09EC83CD-E224-419F-BCF6-DFC1577D5801.thumb.jpeg.afe4927bf67a3e6e3f02cb6a5a6d5f8e.jpeg
Old g sensor showing no signs of heavy impact

9882D95C-8B63-4DF7-801C-9BEB77E1C19D.thumb.jpeg.acbfa396335ca28d712d627eef6a3326.jpeg

new one is a digital g sensor from midori 

3E6AFB02-07C6-4DB7-AEE8-91DAD837A295.thumb.jpeg.63b0e9eb0f2a306efd29f7243664045c.jpeg

and bolted into the car, fits strait onto the original bolt and wiring clips straight in 

This is nice! I want one, where did you order it from? 

  • Like 1
On 11/04/2022 at 9:12 AM, r32-25t said:

Decided seeing as it was 30 years old and are common for dying now I’d replace the g sensor 

09EC83CD-E224-419F-BCF6-DFC1577D5801.thumb.jpeg.afe4927bf67a3e6e3f02cb6a5a6d5f8e.jpeg
Old g sensor showing no signs of heavy impact

9882D95C-8B63-4DF7-801C-9BEB77E1C19D.thumb.jpeg.acbfa396335ca28d712d627eef6a3326.jpeg

new one is a digital g sensor from midori 

3E6AFB02-07C6-4DB7-AEE8-91DAD837A295.thumb.jpeg.63b0e9eb0f2a306efd29f7243664045c.jpeg

and bolted into the car, fits strait onto the original bolt and wiring clips straight in 

Why not the red one ?

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...