Jump to content
SAU Community

Recommended Posts

Looking into getting a kando turbo and recall int he past the internal gates where prone to spiking.

I have heard recently that the issue has been resolved. is this true?

or am i better off spending the extra on an external gate setup

Unless they enlarged the wastegate puck and opened up the hole I would stay well away, stick to the products you know won't boost spike, such as Hypergear or Garrett, or going external gate is the best option imo if you can keep it looking stockish. There are some great gains to be had if an external setup is done right.

Unless they enlarged the wastegate puck and opened up the hole I would stay well away, stick to the products you know won't boost spike, such as Hypergear or Garrett, or going external gate is the best option imo if you can keep it looking stockish. There are some great gains to be had if an external setup is done right.

yeah currently making just over 210kw but was looking at stepping up to a bigger turbo/more power but with similar response.

i had heard the hypergear high flows where laggier than the TD05 18g kandos?

Hypergear do a wide range of turbos with varying flow, some like the SS2 are very responsive for their power capabilities, and run a more modern CNC compressor, much more efficient than an old TD cast compressor. This will add to the cost of course, but I am sure he could make a cast version for similar pricing to the Kando with the same wheels.

Garrett do some nice GTX28 series turbos that would be perfect on an RB20, but you are looking at twice the cost of the kando.

I would contact Tao and speak to him regarding your goals, you have nothing to lose, and it's not something you want to jump into without researching all your options.

definitely worth finding all the options and pricing before i spent the money!

i am getting a leak down test done in the next week to check on the engine health before i even think about buying something :unsure:

Good idea, if it's no good a stock RB25det Neo would get the power you are chasing with no lag at all. :P

yeah det neo would be the path id take if my RB20DE+T dies. but i love the 20's hahah

Another option is to run e85 on the turbo you have now, more power potential just by filling at a different pump, as long as you have the injector overhead. Obviously best if you have a servo nearby that sell it.

I have ported the shit out of my kinugawa td05-18g wastegate hole, it helps but still does creep up to 17+ psi around 5500rpm, on an unopened rb25 with usual basic mods. Although, it seems the turbo works best over 1 bar anyway. Electronic boost controller is used just to bring it on boost, and with the 8cm housing it is defintely not laggy. Have one of the new hypergear hiflows on the way just cos, am keen to see the comparison between the 2.

Another option is to run e85 on the turbo you have now, more power potential just by filling at a different pump, as long as you have the injector overhead. Obviously best if you have a servo nearby that sell it.

Currents mods not really ideal for E85. injectors not big enough for E85 and turbo is the bottle neck as it is.

3_zps09d1fcb4.jpg

RB20DE+T

RB25 turbo (0p6/neo)

R32 GTR injectors

Ebay plenum

R32 GTR cams with solid lifters

profec b spec 2

etc

I have ported the shit out of my kinugawa td05-18g wastegate hole, it helps but still does creep up to 17+ psi around 5500rpm, on an unopened rb25 with usual basic mods. Although, it seems the turbo works best over 1 bar anyway. Electronic boost controller is used just to bring it on boost, and with the 8cm housing it is defintely not laggy. Have one of the new hypergear hiflows on the way just cos, am keen to see the comparison between the 2.

would be interesting see a comparison of the results of the two! be sure to let me know?

guessing you're not in Brisbane from your car pic there but if you are you're welcome to have a drive yourself to check it out before I swap 'em over.(td05 will be for sale cheap too :P, if you were considering one of them)

I have ported the shit out of my kinugawa td05-18g wastegate hole, it helps but still does creep up to 17+ psi around 5500rpm, on an unopened rb25 with usual basic mods. Although, it seems the turbo works best over 1 bar anyway. Electronic boost controller is used just to bring it on boost, and with the 8cm housing it is defintely not laggy. Have one of the new hypergear hiflows on the way just cos, am keen to see the comparison between the 2.

What turbine housing are you running? Any pics? There are a few different versions now...and the latest offering which is a Skyline specific T3 "looks" right compared to the avomination housings they use to offer as their internal gate, T3 offering.

If someone wants a new 18G cheap I have one laying around which is no good to me since my 20 overheated

Roy that 2nd one is the one i use, i have both the 10cm2 and 8cm housings. It is not a physically small turbo, turbine housing is much larger that stock, so i consider its response to be very good, it may not have any boost creep on a lower displacement rb20 with the wastegate ported out?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...